1、Designation:B88109Standard Terminology Relating toAluminum-and Magnesium-Alloy Products1This standard is issued under the fixed designation B881;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in pa
2、rentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This terminology covers the principal terms and defini-tions relating to aluminum-and magnesium-alloy products.Itis published to encourage uniformity
3、of terminology through-out Committee B07 product specifications.1.2 Certain definitions and definitions of terms specific to astandard will remain in the individual standards and will not beincluded in this terminology(see 3.4).2.Referenced Documents2.1 ASTM Standards:2B26/B26M Specification for Alu
4、minum-Alloy Sand Cast-ingsB80 Specification for Magnesium-Alloy Sand CastingsB85 Specification for Aluminum-Alloy Die CastingsB90/B90M Specification for Magnesium-Alloy Sheet andPlateB91 Specification for Magnesium-Alloy ForgingsB92/B92M Specification for Unalloyed Magnesium Ingotand Stick For Remel
5、tingB93/B93M Specification for Magnesium Alloys in IngotForm for Sand Castings,Permanent Mold Castings,andDie CastingsB94 Specification for Magnesium-Alloy Die CastingsB107/B107M Specification for Magnesium-Alloy ExtrudedBars,Rods,Profiles,Tubes,and WireB108 Specification for Aluminum-Alloy Permanen
6、t MoldCastingsB179 Specification for Aluminum Alloys in Ingot and Mol-ten Forms for Castings from All Casting ProcessesB199 Specification for Magnesium-Alloy Permanent MoldCastingsB209 Specification for Aluminum and Aluminum-AlloySheet and PlateB210 Specification for Aluminum and Aluminum-AlloyDrawn
7、 Seamless TubesB211 Specification for Aluminum and Aluminum-AlloyRolled or Cold Finished Bar,Rod,and WireB221 Specification for Aluminum and Aluminum-Alloy Ex-truded Bars,Rods,Wire,Profiles,and TubesB234 Specification for Aluminum and Aluminum-AlloyDrawn Seamless Tubes for Condensers and Heat Ex-cha
8、ngersB236 Specification for Aluminum Bars for Electrical Pur-poses(Bus Bars)B241/B241M Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded TubeB247 Specification for Aluminum and Aluminum-Alloy DieForgings,Hand Forgings,and Rolled Ring ForgingsB308/B308M Specification f
9、or Aluminum-Alloy 6061-T6Standard Structural ProfilesB313/B313M Specification for Aluminum and Aluminum-Alloy Round Welded TubesB316/B316M Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and RodsB317/B317M Specification for Aluminum-Alloy ExtrudedBar,Rod,Tube,Pipe,Structura
10、l Profiles,and Profiles forElectrical Purposes(Bus Conductor)B345/B345M Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube for Gasand Oil Transmission and Distribution Piping SystemsB361 Specification for Factory-Made Wrought Aluminumand Aluminum-Alloy Welding Fit
11、tingsB373 Specification forAluminum Foil for Capacitors(With-drawn 2015)3B403 Specification for Magnesium-Alloy Investment Cast-ingsB404/B404M Specification for Aluminum and Aluminum-Alloy Seamless Condenser and Heat-Exchanger Tubeswith Integral Fins(Withdrawn 2006)3B429/B429M Specification for Alum
12、inum-Alloy ExtrudedStructural Pipe and TubeB479 Specification for Annealed Aluminum and Aluminum-Alloy Foil for Flexible Barrier,Food Contact,and OtherApplications(Withdrawn 2015)31This terminology is under the jurisdiction of ASTM Committee B07 on LightMetals and Alloys and is the direct responsibi
13、lity of Subcommittee B07.03 onAluminum Alloy Wrought Products.Current edition approved June 1,2009.Published July 2009.Originally approvedin 1998.Last previous edition approved in 2005 as B881 05.DOI:10.1520/B0881-09.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM C
14、ustomer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standard
15、Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 B483/B483M Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General PurposeApplicationsB491/B491M Specification for Aluminum and Aluminum-Alloy Extruded Round Tube
16、s for General-Purpose Appli-cationsB547/B547M Specification for Aluminum and Aluminum-Alloy Formed and Arc-Welded Round TubeB594 Practice for Ultrasonic Inspection of Aluminum-AlloyWrought ProductsB618 Specification for Aluminum-Alloy Investment Cast-ingsB632/B632M Specification for Aluminum-Alloy RolledTread PlateB646 Practice for Fracture Toughness Testing of AluminumAlloysB660 Practices for Packaging/Packing of Aluminum andMagnesium ProductsB666/B666M Practice for Identification Marking of Al