1、Designation:A671/A671M16aStandard Specification forElectric-Fusion-Welded Steel Pipe for Atmospheric andLower Temperatures1This standard is issued under the fixed designation A671/A671M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision
2、,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification2covers electric-fusion-welded steelpipe with filler metal added,fabricated from pressure
3、vesselquality plate of several analyses and strength levels andsuitable for high-pressure service at atmospheric and lowertemperatures.Heat treatment may or may not be required toattain the desired properties or to comply with applicable coderequirements.Supplementary requirements are provided forus
4、e when additional testing or examination is desired.1.2 The specification nominally covers pipe 16 in.400mm in outside diameter or larger and of14in.6 mm wallthickness or greater.Pipe having other dimensions may befurnished provided it complies with all other requirements ofthis specification.1.3 Se
5、veral grades and classes of pipe are provided.1.3.1 Grade designates the type of plate used as listed in 5.1.1.3.2 Class designates the type of heat treatment performedduring manufacture of the pipe,whether the weld is radio-graphically examined,and whether the pipe has been pressuretested as listed
6、 in 1.3.3.1.3.3 Class designations are as follows(Note 1):ClassHeat Treatment on PipeRadiography,see SectionPressure Test,see:10nonenonenone11none9none12none98.313nonenone8.320stress relieved,see 5.3.1nonenone21stress relieved,see 5.3.19none22stress relieved,see 5.3.198.323stress relieved,see 5.3.1n
7、one8.330normalized,see 5.3.2nonenone31normalized,see 5.3.29none32normalized,see 5.3.298.333normalized,see 5.3.2none8.340normalized and tempered,see 5.3.3nonenone41normalized and tempered,see 5.3.39none42normalized and tempered,see 5.3.398.343normalized and tempered,see 5.3.3none8.350quenched and tem
8、pered,see 5.3.4nonenone51quenched and tempered,see 5.3.49none52quenched and tempered,see 5.3.498.353quenched and tempered,see 5.3.4none8.370quenched and precipitation heattreatednonenone71quenched and precipitation heattreated9none72quenched and precipitation heattreated98.373quenched and precipitat
9、ion heattreatednone8.3NOTE1Selection of materials should be made with attention totemperature of service.For such guidance,Specification A20/A20M maybe consulted.1.4 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.Within the text,theSI units are show
10、n in brackets.The values stated in eachsystem may not be exact equivalents;therefore,each systemshall be used independently of the other.Combining valuesfrom the two systems may result in non-conformance with thestandard.The inch-pound units shall apply unless the“M”designation of this specification
11、 is specified in the order.2.Referenced Documents2.1 ASTM Standards:3A20/A20M Specification for General Requirements for SteelPlates for Pressure VesselsA370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA435/A435M Specification for Straight-Beam UltrasonicExamination of Steel
12、PlatesA530/A530M Specification for General Requirements forSpecialized Carbon and Alloy Steel PipeA577/A577M Specification for Ultrasonic Angle-Beam Ex-amination of Steel PlatesA578/A578M Specification for Straight-Beam UltrasonicExamination of Rolled Steel Plates for Special Applica-tions1This spec
13、ification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.09 on Carbon Steel Tubular Products.Current edition approved Dec.1,2016.Published December 2016.Originallyapproved in 1972.Last previous edition a
14、pproved in 2016 as A671 16.DOI:10.1520/A0671_A0671M-16A.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SA-671 in Section II of that Code.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual
15、 Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 E110 Test Method fo
16、r Rockwell and Brinell Hardness ofMetallic Materials by Portable Hardness TestersE165/E165M Practice for Liquid Penetrant Examination forGeneral IndustryE709 Guide for Magnetic Particle Testing2.2 Plate Steels:A203/A203M Specification for Pressure Vessel Plates,AlloySteel,NickelA285/A285M Specification for Pressure Vessel Plates,Car-bon Steel,Low-and Intermediate-Tensile StrengthA299/A299M Specification for Pressure Vessel Plates,Car-bon Steel,Manganese-SiliconA353/A353M Specification for Pressu