1、Designation:A94695(Reapproved 2004)Standard Specification forChromium,Chromium-Nickel and Silicon Alloy Steel Plate,Sheet,and Strip for Corrosion and Heat Resisting Service1This standard is issued under the fixed designation A946;the number immediately following the designation indicates the year of
2、original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers alloy steels having a chromiumcontent eq
3、ual to or less than 11.0%in plate,sheet,strip formfor corrosion,and heat-resisting applications.1.2 Some steels covered by this specification,especially thehigh silicon containing steels,because of their particular alloycontent and specialized properties,may require special care intheir fabrication
4、and welding.Specific procedures are offundamental importance,and it is presupposed that all param-eters will be in accordance with approved methods capable ofproducing the desired properties in the finished fabrication.1.3 The values stated in inch-pound units or SI units are tobe regarded separatel
5、y as standard.The values stated in eachsystem are not exact equivalents;therefore,each system mustbe used independently of the other.Combining values from thetwo systems may result in nonconformance with the specifi-cation.1.4 This specification and the applicable material specifica-tions are expres
6、sed in both inch-pound and SI units.However,unless the order specifies the applicable“M”specificationdesignation(SI units),the material shall be furnished ininch-pound units.2.Referenced Documents2.1 ASTM Standards:2A480/A480M Specification for General Requirements forFlat-Rolled Stainless and Heat-
7、Resisting Steel Plate,Sheet,and StripE527 Practice for Numbering Metals and Alloys in theUnified Numbering System(UNS)2.2 SAE Standard:3J 1086 Recommended Practice for Numbering Metals andAlloys(UNS)3.Chemical Composition3.1 The steel shall conform to the requirements as tochemical composition speci
8、fied in Table 1,and shall conformto applicable requirements specified in Specification A480/A480M.4.Mechanical Properties4.1 The material shall conform to the mechanical propertiesspecified in Table 2.5.General Requirements5.1 The following requirements for orders for materialfurnished under this sp
9、ecification shall conform to the appli-cable requirements of the current edition of SpecificationA480/A480M.5.1.1 Definitions,5.1.2 General requirements for delivery,5.1.3 Ordering information,5.1.4 Process,5.1.5 Special tests,5.1.6 Heat treatment,5.1.7 Dimensions and permissible variations,5.1.8 Wo
10、rkmanship,finish,and appearance,5.1.9 Number of tests/test methods,5.1.10 Specimen preparation,5.1.11 Retreatment,5.1.12 Inspection,5.1.13 Rejection and rehearing,5.1.14 Material test report,5.1.15 Certification,and5.1.16 Packaging,marking,and loading.1This specification is under the jurisdiction of
11、 ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.17 on Flat-Rolled and Wrought Stainless Steel.Current edition approved Sept.1,2004.Published September 2004.Originallyapproved in 1995.Last previous edition approved in 2000 as A946-95
12、(2000).DOI:10.1520/A0946-95R04.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Society of Automoti
13、ve Engineers(SAE),400 CommonwealthDr.,Warrendale,PA 15096-0001.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
14、in this standard.Users of this standard are expressly advised that determination of the validity of any such patent rights,and the riskof infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must
15、 be reviewed every five years andif not revised,either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters.Your comments will receive careful consideration at a meeting of theresp
16、onsible technical committee,which you may attend.If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards,at the address shown below.This standard is copyrighted by ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.Individual reprints(single or multiple copies)of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585(phone),610-832-9555(fax),