ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:89.02KB ,
资源ID:187663      下载积分:9 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/187663.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_A_291_-_A_291M_-_16a.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_A_291_-_A_291M_-_16a.pdf

1、Designation:A291/A291M16aStandard Specification forSteel Forgings,Carbon and Alloy,for Pinions,Gears andShafts for Reduction Gears1This standard is issued under the fixed designation A291/A291M;the number immediately following the designation indicates the yearof original adoption or,in the case of

2、revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers normalized and tempered car-bon steel and quenched and tempered alloy stee

3、l forgings forpinions,gears,and shafts.1.2 Several grades of steel are covered as follows:1.2.1 Grade 1,Class A,is normalized and tempered carbonsteel.1.2.2 Grade 2,Class B,Grade 3,Class C,Grade 3A,ClassD,Grades 4 to 7,Classes E,F,G,and H,Grade 8,Class I,andGrade 9,Class J,are liquid quenched and te

4、mpered alloy steel.1.3 All grades and classes are considered weldable underproper conditions.Welding technique is of fundamental impor-tance and it is presupposed that welding procedure andinspection shall be in accordance with approved methods forthe class of material used.1.4 The values stated in

5、either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.5 This standar

6、d does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Sta

7、ndards:2A275/A275M Practice for Magnetic Particle Examination ofSteel ForgingsA388/A388M Practice for Ultrasonic Examination of SteelForgingsA788/A788M Specification for Steel Forgings,General Re-quirements3.Terminology3.1 Definitions:3.1.1 gearsrings,disks,cylinders or rectangular bars hav-ing gear

8、 teeth.3.1.2 pinionscircular cross section forgings of multiplediameter with gear teeth on one or more diameters.3.1.3 shaftscircular cross section forgings of one or morediameters which do not have integral gear teeth.4.Ordering Information4.1 Instructions for purchasing forgings to this specificat

9、ionshould be in accordance with Specification A788/A788M.Inaddition,a detailed drawing,sketch,or written description ofthe forging should be included with the inquiry or order.4.2 Supplementary requirements are provided and shallapply only when specified in the purchase order.5.Heat Treatment5.1 Pre

10、liminary Heat Treatment:5.1.1 The forgings shall be given such preliminary heattreatment as is proper for the design and composition.Theforgings shall be heated to a suitable temperature for asufficient length of time for austenitization and shall be suitablycooled to bring about complete transforma

11、tion.5.1.2 Forgings may be immediately treated for mechanicalproperties after preliminary heat treatment or may be roughturned prior to treatment for mechanical properties.5.2 Heat Treatment for Mechanical PropertiesThe forg-ing shall be reheated to a temperature above the upper criticaltemperature

12、and held a sufficient length of time for completeaustenitization.Grade 1 shall be air cooled while Grades 2through 9 shall be liquid quenched.5.3 TemperingThe forgings shall be tempered to developthe specified properties.Minimum tempering temperaturesshall be as follows:1This specification is under

13、the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.06 on Steel Forgings and Billets.Current edition approved Dec.1,2016.Published December 2016.Originallyapproved in 1946.Last previous edition approved in 2016 as A29

14、1/A291M 16.DOI:10.1520/A0291_A0291M-16A.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes sect

15、ion appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 Minimum Tempering TemperatureGradeClassFC1 and 2A and B11506203,3A,and 4C,D,and E10755805,6,7F,G,and H10505658I11005959J1000540The charge shall be cool

16、ed under uniform conditions in thefurnace at a maximum rate of 100 F 55 C per h to 600 F315 C.5.4 Stress ReliefIf the manufacturer elects to heat treat formechanical properties prior to machining,the forgings shall bestress relieved after machining(see 5.5)at a temperature that is50 to 100 F 30 to 55 C below the last previous temperingtemperature but in no case below 1000 F 540 C.Theforgings shall be cooled under uniform conditions in thefurnace at a maximum rate of 100 F 55 C h to 600 F315 C.5.

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2