ImageVerifierCode 换一换
格式:PDF , 页数:4 ,大小:110.76KB ,
资源ID:187810      下载积分:13 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/187810.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_A_717_-_A_717M_-_12.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_A_717_-_A_717M_-_12.pdf

1、Designation:A717/A717M12Standard Test Method forSurface Insulation Resistivity of Single-Strip Specimens1This standard is issued under the fixed designation A717/A717M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the year of last

2、revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers a means of testing the surfaceinsulation resistivity of single strips or punchings of flat-rolledelectr

3、ical steel under predetermined conditions of voltage,pressure,and temperature.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the oth

4、er.Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and

5、 determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2A34/A34M Practice for Sampling and Procurement Testingof Magnetic Materials3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 surface insulation resistivityrefers to the

6、effectiveresistivity of a single insulative layer tested between appliedbare metal contacts and the base metal of the insulated testspecimen.It is not the same as the terms interlaminar resistivityand stack resistivity,which refer to the average resistivity oftwo adjacent insulative surfaces in cont

7、act with each other.3.1.2 The apparatus is popularly known as a Franklin tester.4.Summary of Test Method4.1 Ten metallic contacts of fixed area are applied to one ofthe surfaces of the specimen and electrical contact is made withthe base metal by two drills.The effectiveness of the surfaceinsulation

8、 is then indicated by a measurement of averageelectrical current flowing between the contacts and the basemetal under specified applied voltage.This measurement canbe used directly as an indicator of insulation quality or may beconverted to an apparent surface insulation resistivity value.5.Signific

9、ance and Use5.1 This test method is particularly suitable for qualitycontrol in the application of insulating coatings.5.2 Surface insulation resistivity is evaluated from a dccurrent that can range from 0(perfect insulator)to 1 A(perfectconductor).5.3 Single readings should not be considered signif

10、icantsince the nature of the test device and specimen are such thatsuccessive measurements of a specimen often yield differentvalues.6.Apparatus6.1 The apparatus,as shown in Fig.1 and Fig.2,shallconsist of a contact unit or test head which is attached to thehead of a hydraulic press.Its associated m

11、easuring equipment,which may be remotely located,includes an ammeter,voltmeter,and voltage regulated dc power supply.Whenmeasurements are to be made at elevated temperatures,theplaten beneath the specimen is heated and controlled.Detaileddescriptions of the various components are given in AnnexA1.7.

12、Sampling7.1 Samples shall be representative of the steel and shall becut in a manner to assure representative sampling as describedin Practice A34/A34M.8.Test Specimen8.1 The width and length of a specimen strip shall be greaterthan the width and length respectively of the assembly ofcontacts.The su

13、ggested minimum specimen size is 2 by 5 in.50 by 130 mm.8.2 A minimum of five specimen strips is recommended.1This test method is under the jurisdiction of ASTM Committee A06 onMagnetic Properties and is the direct responsibility of Subcommittee A06.01 on TestMethods.Current edition approved May 1,2

14、012.Published July 2012.Originally approvedin 1975.Last previous edition approved in 2006 as A717/A717M 06.DOI:10.1520/A0717_A0717M-12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume informa

15、tion,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 8.3 By mutual agreement between the producer and theuser,tests may be run on Epstein test strips.The Epsteinspecimens may

16、 be less satisfactory than the minimum sizespecimen suggested in 8.1 because of the tilting effect due toburrs,shearing strains,and disturbances in the coating.9.Procedure9.1 To ensure correct contact button conditions,make ashort circuit test occasionally by testing a bare metal surface.When the short circuit current is less than 0.99 A,clean thecontacts.The use of solvents for cleaning is preferred toabrasives because the latter can result in rounded tips withreduced contact areas.9.2 The reco

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2