1、Designation:F 1509 94(Reapproved 2004)Standard Test Methods forDetermining Acceptability of Ribbon Welds in FabricCartridges1This standard is issued under the fixed designation F 1509;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,t
2、he year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.1.Scope1.1 These test methods are for evaluating ribbon welds infabric cartridges that do not contain endless woven loops.
3、These test methods apply to ribbon welds made with ultrasonicenergy but do not cover special-purpose welds such as overlapor butt welds.Physical characteristics of ribbon welds and testperformance may be used to predict acceptable function andprinting life of the weld in the finished cartridge.These
4、 testmethods are suitable both for comparative evaluations byend-users and for manufacturing control within the ribbonproduct industry.1.2 Since types of ribbon welds and equipment vary,similarfabric cartridges may not contain the same type of ribbon weld.Any evaluation comparing products from diffe
5、rent sourcesshould note this.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations pr
6、ior to use.2.Referenced Documents2.1 ASTM Standards:2F 1174 Practice for Using a Personal Computer as a TestInstrument3.Terminology3.1 Definition3.1.1 hot spottingprinted images produced with an inkedfabric ribbon where occasional individual images are darkerthan those around them;this condition occ
7、urs when the amountof ink is not consistent throughout the fabric ribbon.4.Summary of Test Methods4.1 Fabric ribbon welds can be evaluated on the basis of thefollowing characteristics:4.1.1 Appearance,4.1.2 Width,4.1.3 Alignment,4.1.4 Strength,4.1.5 Printability,and4.1.6 Durability.4.2 Test methods
8、for evaluating welds in these areas aredescribed.These test methods are divided into sections byribbon weld characteristic.Each section consists of a testprocedure,results that can be obtained,and what these resultsmay indicate.Each user must determine the tests that arereasonable considering the ne
9、eds and the equipment available.5.Significance and Use5.1 The test methods described can be used to evaluateacceptability of fabric ribbon welds on a comparative basis.Some,though not all,tests may also be used for manufacturingcontrol.The weld durability test is exclusively for manufac-turing contr
10、ol,since it involves in-process testing.5.2 Users may choose to perform any or all of the testsdescribed,depending upon results desired and equipmentavailable.6.Interferences6.1 Interferences that may impact test results are listed foreach test method to which they apply.6.2 Weld WidthWeld width is
11、best determined with theuse of polarized light,due to the difference between filamentdeformation and physical property changes(that is,melting).6.3 Weld Strength:6.3.1 The type of welding equipment used and operatortechnique may cause variability in weld strength.For weldequipment that does not auto
12、matically tension the fabric,thetension applied by the operator when securing the fabric in thefixture can significantly alter the weld strength.6.3.2 The type of nylon,thickness,style,finishing,andslitting of the fabric may cause variability in weld strength.Inkproperties and level of inking of the
13、 fabric also contribute to1These test methods are under the jurisdiction of ASTM Committee F05 onBusiness Imaging Products and are the direct responsibility of SubcommitteeF05.02 on Inked Transfer Imaging Products.Current edition approved Dec.1,2004.Published December 2004.Originallyapproved in 1994
14、.Last previous edition approved in 2000 as F 1509 94(2000).2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.1Copyri
15、ght ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.variability in optimum weld strength.Such ink characteristicsas oil color carriers,type of solids,if present,and quality ofdispersion may be considered.Samples being compared shouldbe classified as
16、 closely as possible and tested under equalconditions.6.4 Weld Printability:6.4.1 Certain types of ribbon welds may cause print defectspeculiar to the type of weld.Some welds are not designed to beoverprintable.6.4.2 Some types of ink formulations and nylon types willbe more prone to hotspotting than others.Hotspotting at theweld could,therefore,be a function of the material rather thanthe welding process.Note evidence of hotspotting elsewhere inprintout.6.5 Weld Durability:6.5.1 The zipper test