1、Designation:F148814Standard Specification forCoextruded Composite Pipe1This standard is issued under the fixed designation F1488;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indica
2、tes the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers coextruded composite pipe,produced by a coextrusion die system,in which the concentriclayers are formed and combined before exiting the die.
3、1.1.1 The function of this specification is to provide stan-dardization of product,to produce technical data,and to serveas a purchasing guide.1.2 Compounds that do not meet the requirements of thematerial section are excluded.1.3 The coextruded composite pipe is permitted to beperforated in accorda
4、nce with any specified standard or byagreement between the purchaser and the supplier.1.4 The coextruded composite pipe is permitted to be belledfor joining by solvent cementing or belled for joining by anelastomeric seal(gaskets),in accordance with any specifiedstandard or by agreement between the
5、purchaser and thesupplier.1.5 Recommendations for storage,joining,installation,andrationale are listed in Appendix X1,Appendix X2,AppendixX3,and Appendix X4,respectively.1.6 The values stated in inch-pound units are to be regardedas standard.No other units of measurement are included in thisstandard
6、.1.7 The text of this specification references notes,footnotes,and appendixes which provide explanatory material.Thesenotes and footnotes(excluding those in tables and figures)shallnot be considered as requirements of this specification.1.8 This standard does not purport to address all of thesafety
7、concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.NOTE1Related specifications are as follows:D2661,D2665,D2729,D2750,D2751,D2949,D3
8、034,F512,F628,F758,F789,and F891.2.Referenced Documents2.1 The following standards contain provisions which,though referenced in this specification,constitute provisions ofthis specification.All standards are subject to revision andparties using this specification shall reference the most recentedit
9、ion of the standards listed as follows.2.2 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD696 Test Method for Coefficient of Linear Thermal Expan-sion of Plastics Between 30C and 30C with a VitreousSilica DilatometerD883 Terminology Relating to PlasticsD1600 Terminology forAbbre
10、viated Terms Relating to Plas-ticsD1898 Practice for Sampling of Plastics(Withdrawn 1998)3D1972 Practice for Generic Marking of Plastic Products(Withdrawn 2014)3D2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2235 Specification for Solvent Cement for Acrylonitrile-Bu
11、tadiene-Styrene(ABS)Plastic Pipe and FittingsD2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determin
12、ation of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D2564 Specification for Solvent Cements for Poly(VinylChloride)(PVC)Plastic Piping SystemsD2661 Specification for Acrylonitrile-Butadiene-Styrene(ABS)Schedule 40 Plastic Drain,Waste,and Vent Pipeand Fi
13、ttingsD2665 Specification for Poly(Vinyl Chloride)(PVC)PlasticDrain,Waste,and Vent Pipe and FittingsD2729 Specification for Poly(Vinyl Chloride)(PVC)SewerPipe and Fittings1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of
14、Subcommittee F17.11 onComposite.Current edition approved Dec.1,2014.Published January 2015.Originallyapproved in 1994.Last previous edition approved in 2009 as F1488 091.DOI:10.1520/F1488-14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at service
15、astm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM Internation
16、al,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 D2750 Specification for Acrylonitrile-Butadiene-Styrene(ABS)Plastics Utilities Conduit and Fittings(Withdrawn1997)3D2751 Specification for Acrylonitrile-Butadiene-Styrene(ABS)Sewer Pipe and Fittings(Withdrawn 2014)3D2855 Practice for Making Solvent-Cemented Joints withPoly(Vinyl Chloride)(PVC)Pipe and FittingsD2949 Specification for 3.25-in.Outside Diameter Poly(Vi-nyl Chloride)(PVC)Plastic Drain,Waste,and Vent P