1、Designation:F2762111Standard Specification for12 to 30 in.(300 to 750 mm)Annular Corrugated Profile-WallPolyethylene(PE)Pipe and Fittings for Sanitary SewerApplications1This standard is issued under the fixed designation F2762;the number immediately following the designation indicates the year ofori
2、ginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEUnits statement(1.4)was editorially revised in October 2013.1.Scope1.1 This
3、 specification covers requirements and test methodsfor annular,corrugated profile wall polyethylene pipe andfittings with an interior liner.The nominal inside diameterscovered are 12 to 30 in.(300 to 750 mm).1.2 The requirements of this specification are intended toprovide pipe and fittings suitable
4、 for underground use fornon-pressure sanitary sewer systems.Pipe and fittings pro-duced in accordance with this specification shall be installed incompliance with Practice D2321.1.3 This specification covers pipe and fittings with aninterior liner using a corrugated exterior profile(Fig.1).1.4 Units
5、The values stated in inch-pound units are to beregarded as standard.The values given in parentheses aremathematical conversions to SI units that are provided forinformation only and are not considered standard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated
6、with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2A666 Specification for Annealed or Cold-Worked AusteniticStainless
7、 Steel Sheet,Strip,Plate,and Flat BarD618 Practice for Conditioning Plastics for TestingD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2321 Practice for Underground Installation of Thermoplas-tic Pipe for S
8、ewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D3212 Specificatio
9、n for Joints for Drain and Sewer PlasticPipes Using Flexible Elastomeric SealsD3350 Specification for Polyethylene Plastics Pipe and Fit-tings MaterialsD4389 Specification for Finished Glass Fabrics Woven FromRovingsF412 Terminology Relating to Plastic Piping SystemsF477 Specification for Elastomeri
10、c Seals(Gaskets)for Join-ing Plastic PipeF2136 Test Method for Notched,Constant Ligament-Stress(NCLS)Test to Determine Slow-Crack-Growth Resis-tance of HDPE Resins or HDPE Corrugated Pipe2.2 AASHTO Standard:3LRFD,Section 12 AASHTO LRFD Bridge Design Specifi-cations Section 12 Buried Structures and T
11、unnel Liners2.3 Federal Standard:4Fed.Std.No.123 Marking for Shipment(Civil Agencies)2.4 Military Standard:4MIL-STD-129 Marking for Shipment and Storage3.Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F412 and abbreviations are in accordance with Termi-nology D1600,unless
12、otherwise specified.The abbreviation forpolyethylene is PE.1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.Current edition approved Jan.1,2011.Published January 2011.DOI:10.1520/F276211.2For
13、 referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American Association of State Highway and Transportati
14、onOfficials(AASHTO),444 N.Capitol St.,NW,Suite 249,Washington,DC 20001,http:/www.transportation.org.4Available from Standardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/dodssp.daps.dla.mil.Copyright ASTM International,100 Barr Harbor Drive,PO Box
15、 C700,West Conshohocken,PA 19428-2959.United States1 3.2 Definitions of Terms Specific to This Standard:3.2.1 profile wall,nIn this case,the profile pipe wallconstruction provides an interior liner in the waterway andincludes ribs,corrugations,or other shapes,which can be eithersolid or hollow,that
16、helps brace the pipe against diametricaldeformation.4.Ordering Information4.1 Orders for product made to this specification shallinclude the following information to adequately describe thedesired product:4.1.1 This ASTM designation and year of issue,4.1.2 Diameters,4.1.3 Total footage of each pipe diameter involved,4.1.4 Pipe laying length,4.1.5 Fitting type(s):4.1.5.1 Size and type of fittings,including mainline andbranch diameters,and4.1.5.2Number of fittings per diameter.5.Materials and Manu