ImageVerifierCode 换一换
格式:PDF , 页数:13 ,大小:244.44KB ,
资源ID:189140      下载积分:10 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/189140.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_F_3038_-_14.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_F_3038_-_14.pdf

1、Designation:F303814Standard Test Method forTimed Evaluation of Forced-Entry-Resistant Systems1This standard is issued under the fixed designation F3038;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A numbe

2、r in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method sets forth the requirements and testingprocedures to test forced-entry-resistant building components,construction components,an

3、d specialty security equipment.This test method is intended primarily for manufacturers to testand rate their windows,doors,modular panels,glazings,louvers,walls,seismic joints,roofs,roof hatches,grilles,andsimilar products to ensure that all manufactured products meetthe necessary requirements for

4、forced-entry protection.1.2 This test method is currently designed to simulate aspontaneous mob using readily available hand tools as theprimary threat for forced entry.1.3 In order to receive a rating,all portions of the testedspecimen must meet or exceed the test level.1.4 Systems are required to

5、be tested as complete units in atest frame or fielded conditions.Mulled systems must be testedin the mulled condition.Test results only apply to the compo-nent or system as tested.Once a system is tested and deemedto satisfy the requirements of this test method,no designchange can be made without a

6、retest.1.5 UnitsThe values stated in this standard are SI unitswith the exception of the nominal descriptors for tools.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate

7、 safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2E631 Terminology of Building ConstructionsE2771 Terminology for Homeland Security ApplicationsF1915 Test Methods for Glazing for Detention Facilities2.2 Othe

8、r Standards:SD-STD-01.01 Forced-Entry and Ballistic-Resistance ofStructural Systems,Rev.G(Amended)3ISO/IEC 17025:2005 General Requirements for the Compe-tence of Testing and Calibration Laboratories43.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 componentintegral part of a for

9、ced entry test speci-men such as:panels,frame,glazing,glazing bite,flanges,hinges,locks,jamb/wall,jamb/strike mullions,and mountingdevices of different shape,size,and material.3.1.2 door,doubletwo-door assembly with an openingtwice as wide as a single door with a common latch and lockedge.3.1.3 inde

10、pendent test facilitytesting laboratory accreditedto perform the referenced testing procedures by a nationallyrecognized accrediting agency in accordance with ISO/IEC17025.3.1.4 individual systemsindividual doors,windows,louvers,hatches,grilles,or wall panels.The doors,windows,and panels may have on

11、e transparency or two or moretransparencies separated with a mullion.3.1.5 louversangled and gapped slats which permit thepassage of air through an otherwise impassable barrier.Whilelouvers usually are rigidly constructed,the slats may bemoveable to seal off air passage.3.1.5.1 manufacturer-delivere

12、d systemsincludes both in-dividual and mulled systems.3.1.6 mulliona component used to divide two parts of thesame system and it can be vertical or horizontal,movable orfixed.For purposes of this test method,a mullion does notinclude steel or concrete structural members(including seismicjoints)which

13、 are present in the building.3.1.7 mulledthe physical connection together of two partsof the same system.The two systems may be anchored directlyto each other or have a mullion between them.1This test method is under the jurisdiction ofASTM Committee F12 on SecuritySystems and Equipment and is the d

14、irect responsibility of Subcommittee F12.10 onSystems Products and Services.Current edition approved April 15,2014.Published May 2014.DOI:10.1520/F3038-14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStan

15、dards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from U.S.Government Printing Office Superintendent of Documents,732 N.Capitol St.,NW,Mail Stop:SDE,Washington,DC 20401,http:/www.access.gpo.gov.4Available from International Organization for Standardi

16、zation(ISO),1,ch.dela Voie-Creuse,CP 56,CH-1211 Geneva 20,Switzerland,http:/www.iso.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.1.8 ready-to-installfabricated,with an appropriate finalfinish such as galvanizing,paint,or anodizing.The testspecimen shall consist of the entire fenestration assembly andcontain all devices used to resist forced entry.All parts of thetest specimen shall be full size,as specified for actual use,usi

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2