1、Designation:F261819An American National StandardStandard Specification forChlorinated Poly(Vinyl Chloride)(CPVC)Pipe and Fittingsfor Chemical Waste Drainage Systems1This standard is issued under the fixed designation F2618;the number immediately following the designation indicates the year oforigina
2、l adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers the performance requirementsof CPVC pipe,fitti
3、ngs and solvent cements used in chemicalwaste drainage systems.1.2 Asystem is made up of pipe,fittings and solvent cementthat meet the requirements of this standard.NOTE1Consult the manufacturers chemical resistance recommenda-tions for chemical waste drainage applications prior to use.1.3 The text
4、of this specification references notes,footnotesand appendices that provide explanatory material.These notesand footnotes(excluding those in tables and figures)shall notbe considered as requirements of the specification.1.4 The pressure tests described in this standard are labora-tory hydrostatic te
5、sts that are intended to verify joint/systemintegrity.They are not intended for use as field tests of installedsystems.1.5 Due to inherent hazards associated with testing compo-nents and systems with compressed air or other compressedgases,no such testing shall be done unless the componentmanufactur
6、er gives approval in writing.NOTE2Pressurized(compressed)air or other compressed gasescontain large amounts of stored energy,which present serious safetyhazards should a system fail for any reason.1.6 Mechanical joints used for joining pipe and fittings ofdifferent materials are provided for in this
7、 specification.Theyinclude common flanges,couplings,and unions.1.7 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.8 This standard does
8、not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.NOTE3This specification spe
9、cifies dimensional,performance,andtest requirements for fluid handling applications but does not addressventing of combustion gases.1.9 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles fo
10、r theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D543 Practices for Evaluating the Resistance of Plastics toChemical ReagentsD618 Practice for Conditioning
11、 Plastics for TestingD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1784 Specification for Rigid Poly(Vinyl Chloride)(PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC)CompoundsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2321 Practice for Unde
12、rground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Practice for Determination of the Impact Resistanceof Thermoplastic Pipe and Fittings by Mea
13、ns of a Tup(Falling Weight)D3311 Specification for Drain,Waste,and Vent(DWV)Plastic Fittings PatternsF402 Practice for Safe Handling of Solvent Cements,Primers,and Cleaners Used for Joining ThermoplasticPipe and FittingsF412 Terminology Relating to Plastic Piping SystemsF493 Specification for Solven
14、t Cements for ChlorinatedPoly(Vinyl Chloride)(CPVC)Plastic Pipe and FittingsF1498 Specification for Taper Pipe Threads 60 for Thermo-plastic Pipe and Fittings1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee
15、F17.63 on DWV.Current edition approved Jan.1,2019.Published January 2019.Originallyapproved in 2009.last previous edition approved in 2015 as F261815.DOI:10.1520/F2618-192For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual B
16、ook of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recomm