1、Designation:F303013Standard Test Method forSnowboards with a Channel-Mounting System andRemovable Inserts1This standard is issued under the fixed designation F3030;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revi
2、sion.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the requirements and testmethod for snowboards with channel-mounting systems onwhich bindings are attached t
3、o the board by means of aremovable insert and screws.1.2 This test method does not apply to snowboards forchildren with a mass less than 25 kg.It contains data for themanufacturer of snowboards,bindings,and retention devicesconcerning dimensions,tests,and other specifications for thebinding mounting
4、 area.1.3 For snowboards with fixed inserts,see ISO 10958-2.1.4 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is therespo
5、nsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2E177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE691 Practice for Co
6、nducting an Interlaboratory Study toDetermine the Precision of a Test Method2.2 ISO Standards:3ISO 68-1 ISO general purpose screw threads-Basic profile-Part 1:Metric screw threadsISO 10958-2 Requirements and test methods for snowboardswith fixed inserts3.Terminology3.1 Definitions:3.1.1 channel,nreu
7、sable metal attachment slot perma-nently fixed in the snowboard at the time of manufacture usedto mount the bindings to the snowboard via removablethreaded inserts.3.1.2 insert,nreusable commonly threaded attachmentpoint,removable from the channel in the snowboard,used tomount the bindings to the sn
8、owboard.3.1.3 retention strength,naxial pull-out force of an insertin a snowboard tested in accordance with 5.1 and 8.1.3.1.4 screw thread engagement,nnumber of threads en-gaged by a standard screw in an insert.4.Significance and Use4.1 This test method is intended for use in evaluating thebinding t
9、o snowboard insert retention strength resulting fromuse.This test method may also be used to compare thedurability of different materials and designs.This test methodreferences ISO 10958-2,which is considered satisfactory foracceptance testing insert retention for snowboards.5.Apparatus5.1 Retention
10、 Strength Test ApparatusUniversal test ma-chine(UTM),with a pull-out device according to Fig.1,having a minimum load range of 10 kN.5.2 The pullout device should consist of:5.2.1 A rigid steel attachment plate(A)with one hole of6.5-mm diameter,5.2.2 An insert(B)located in the snowboard channel andbo
11、lted through the hole of(A),5.2.3 A universal joint(C)that is connected to the attach-ment plate and the clamping device of the test machine,and5.2.4 A snowboard support(D)with two rollers and span of200 mm between them.6.Specifications for Design of Snowboard Channel andInsert6.1 Inserts shall have
12、 an M6 1.0,Class 6H internal threadwith standard tolerances in accordance with ISO 68-1.1This test method is under the jurisdiction of ASTM Committee F27 on SnowSkiing and is the direct responsibility of Subcommittee F27.30 on Skiing andSnowboarding Equipment.Current edition approved Oct.1,2013.Publ
13、ished October 2013.DOI:10.1520/F3030-13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Internatio
14、nal Organization for Standardization(ISO),1,ch.dela Voie-Creuse,CP 56,CH-1211 Geneva 20,Switzerland,http:/www.iso.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.2 Insert screws shall have an M6 1.0,Class 6g externalthread with stan
15、dard tolerances in accordance with ISO 68-1.6.3 The snowboard design shall provide a minimum screwengagement of three threads.The length of the screw shallallow a gap between the end of the screw and the bottom of thechannel.The value of three threads of engagement has beenverified by extensive test
16、s carried out by snowboard manufac-turers.It is recommended that self-locking screws are used.7.Strength Requirements7.1 Retention StrengthWhen tested in accordance withSection 9,the channel in a snowboard shall have a minimumretention strength of 4500 N for those snowboards with asuggested rider mass of 45 kg or more and a minimumretention strength of 3500 N for those snowboards with asuggested rider mass between 25 and 45 kg.8.Conditioning8.1 Test the snowboards at room temperature,23 6 5C.9.P