1、Designation:F2306/F2306M141Standard Specification for12 to 60 in.300 to 1500 mm Annular Corrugated Profile-Wall Polyethylene(PE)Pipe and Fittings for Gravity-FlowStorm Sewer and Subsurface Drainage Applications1This standard is issued under the fixed designation F2306/F2306M;the number immediately f
2、ollowing the designation indicates the yearof original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTETable 1 was editorially c
3、orrected in March 2015.1.Scope*1.1 This specification covers requirements and test methodsfor annular,corrugated profile wall polyethylene pipe andfittings with an interior liner.The nominal inside diameterscovered are 12 to 60 in.300 to 1500 mm.1.2 The requirements of this specification are intende
4、d toprovide pipe and fittings suitable for underground use forgravity-flow storm sewer and subsurface drainage systems.NOTE1Pipe and fittings produced in accordance with this specifica-tion shall be installed in compliance with Practice D2321.1.3 This specification covers pipe and fittings with anin
5、terior liner using a corrugated exterior profile(Fig.1).1.4 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard.Thevalues stated in each system may not be exact equivalents;therefore,each system shall be used independently of the other.Combining va
6、lues from the two systems may result in non-conformance with the standard.1.5 The following precautionary caveat pertains only to thetest method portion,Section 7,of this specification.Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the respon
7、sibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1600 Terminology forAbbreviated Terms Relatin
8、g to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Par
9、allel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D3212 Specification for Joints for Drain and Sewer PlasticPipes Using Flexible Elastomeric SealsD3350 Specification for Polyethylene Plastics Pipe and F
10、it-tings MaterialsF412 Terminology Relating to Plastic Piping SystemsF477 Specification for Elastomeric Seals(Gaskets)for Join-ing Plastic PipeF2136 Test Method for Notched,Constant Ligament-Stress(NCLS)Test to Determine Slow-Crack-Growth Resis-tance of HDPE Resins or HDPE Corrugated Pipe2.2 AASHTO
11、Standard:3AASHTO LRFD Bridge Design SpecificationsLRFD,Section 12 Bridge Design Specifications Section 12 Buried Structures and Tunnel LinersAASHTO M 145:Classification of Soils and AggregateMixtures2.3 Department of Agriculture Standard:Standard 606 Soil Conservation Service Engineering42.4 Federal
12、 Standard:Fed.Std.No.123 Marking for Shipment(Civil Agencies)51This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.Current edition approved Nov.1,2014.Published December 2014.Originallyapproved i
13、n 2005.Last previous edition approved in 2013 as F2306/F2306M 13.DOI:10.1520/F2306_F2306M-14E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Su
14、mmary page onthe ASTM website.3Available from American Association of State Highway and TransportationOfficials(AASHTO),444 N.Capitol St.,NW,Suite 249,Washington,DC 20001,http:/www.transportation.org.4Available from U.S.Government Printing Office Superintendent of Documents,732 N.Capitol St.,NW,Mail
15、 Stop:SDE,Washington,DC 20401.http:/www.gpo.gov/about/bookstore.htm5DLA Document Services Building 4/D 700 Robbins Avenue Philadelphia,PA19111-5094 http:/quicksearch.dla.mil/*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C70
16、0,West Conshohocken,PA 19428-2959.United States1 2.5 Military Standard:MIL-STD-129 Marking for Shipment and Storage52.6 NCHRP(National Cooperative Highway Research Pro-gram)Report:6NCHRP Report 631 Updated Test and Design Methods forThermoplastic Drainage Pipe3.Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F412 and abbreviations are in accordance with Termi-nology D1600,unless otherwise specified.The abbreviation forpolyethylene is PE.3.2 Definitions of Terms Specific