ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:94.69KB ,
资源ID:190037      下载积分:10 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/190037.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_F_459_-_13.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_F_459_-_13.pdf

1、Designation:F45913Standard Test Methods forMeasuring Pull Strength of Microelectronic Wire Bonds1This standard is issued under the fixed designation F459;the number immediately following the designation indicates the year of originaladoption or,in the case of revision,the year of last revision.Anumb

2、er in parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 These test methods cover tests to determine the pullstrengt

3、h of a series of wire bonds.Instructions are provided tomodify the methods for use as a referee method.The methodscan be used for wire bonds made with wire having a diameterof from 0.0007 to 0.003 in.(18 to 76 m).NOTE1Common usage at the present time considers the term“wirebond”to include the entire

4、 interconnection:both welds and the interven-ing wire span.1.2 These test methods can be used only when the loopheight of the wire bond is large enough to allow a suitable hookfor pulling(see Fig.1)to be placed under the wire.1.3 The precision of these methods has been evaluated foraluminum ultra-so

5、nic wedge bonds;however,these methodscan be used for gold and copper wedge or ball bonds.21.4 These methods are destructive.They are appropriate foruse in process development or,with a proper sampling plan,forprocess control or quality assurance.1.5 A nondestructive procedure is described in Practic

6、eF458.1.6 The values in SI units are to be regarded as standard.1.7 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-

7、bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:3F458 Practice for Nondestructive Pull Testing of Wire Bonds3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 For the purposes of these test methods the followingfailure points are defined:3.1.

8、2 bond-wire junction failurea rupture in the wirewithin two wire diameters of the bond and in which more than25%of the bonded area is left on the pad after the pull test hasbeen applied.3.1.3 weld interface failurea rupture in which less than25%of the bonded area is left on the pad after the pull te

9、st hasbeen applied.See pad lifting in 6.6.3.1.4 wire span failurea rupture in the wire other than(1)at a point within two wire diameters of either bond,or(2)at thepoint at which the hook contacted the wire.4.Summary of Test Methods4.1 The microelectronic device with the wire bond to betested is held

10、 firmly in an appropriate fixture.A hook ispositioned under the wire midway between the two bonds.Thehook is then raised until the wire bond breaks.The forceapplied to the hook in order to cause failure of the wire bondis recorded.The point of failure is observed and recorded.Inthe referee method,th

11、e force in the wire on breaking iscalculated.5.Significance and Use5.1 Failure of microelectronic devices is often due to failureof an interconnection bond.A common type of interconnectionbond is a wire bond.These methods can assist in maintaining1These test methods are under the jurisdiction of AST

12、M Committee F01 onElectronics and are the direct responsibility of Subcommittee F01.03 on MetallicMaterials,Wire Bonding,and Flip Chip.Current edition approved Jan.1,2013.Published January 2013.Originallyapproved in 1976 as F459 76 T.Last previous edition approved in 2006 asF459 06.DOI:10.1520/F0459

13、-13.2Harman,G.G.,”Microelectronic Ultrasonic Bonding,”NBS Special Publica-tion 400-2,pp.94-95 and“Wire Bonding in Microelectronics,”Third Edition,McGraw Hill,2010.Also Microelectronics Reliability 51(2011),Special Issue onCopper bonding.3For referenced ASTM standards,visit the ASTM website,www.astm.

14、org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 control of the proc

15、ess of making wire bonds.They can be usedto distinguish between weak,nonadherent wire bonds andacceptably strong wire bonds.The methods are destructive.5.2 These test methods are appropriate for on-line use forprocess control,for purchase specifications,and for research insupport of improved yield o

16、r reliability.The referee methodshould be used for quantitative comparison of pull strengths ofwire bonds.6.Interferences6.1 Failure to center the hook along the loop between thetwo bonds or pulling in a direction not lying in the planecontaining the undisturbed loop may invalidate the test since anunbalanced distribution of forces between the two bonds mayresult.6.2 Slippage of the hook along the wire span during pullingmay invalidate the test because an unbalanced distribution offorces between

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2