1、Designation:F78201(Reapproved 2012)An American National StandardStandard Specification forDoors,Furniture,Marine1This standard is issued under the fixed designation F782;the number immediately following the designation indicates the year of originaladoption or,in the case of revision,the year of las
2、t revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers the construction
3、of furnituredoors for use where invoked by other marine furniture speci-fications.1.2 This specification applies to all furniture doors formarine furniture,in items requiring hinged doors.1.3 Values stated in inch-pound units are to be regarded asthe standard.The metric equivalents,given in parenthe
4、ses,arefor information only.2.Referenced Documents2.1 ASTM Standards:2A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate,Sheet,and Strip for PressureVessels and for General ApplicationsA1008/A1008M Specification for Steel,Sheet,Cold-Rolled,Carbon,Structural,High-Strength
5、 Low-Alloy,High-Strength Low-Alloy with Improved Formability,SolutionHardened,and Bake HardenableA582/A582M Specification for Free-Machining StainlessSteel BarsB209 Specification for Aluminum and Aluminum-AlloySheet and PlateB221 Specification for Aluminum and Aluminum-Alloy Ex-truded Bars,Rods,Wire
6、,Profiles,and TubesC1036 Specification for Flat GlassD907 Terminology of AdhesivesF2119 Test Method for Evaluation of MR Image Artifactsfrom Passive Implants2.2 American Institute of Steel Construction Manual:3AISC Wire and Sheet Metal GagesEquivalent Thicknessin Decimals of an Inch,U.S.Standard Gag
7、e(USSG)forUncoated Hot and Cold-Rolled Sheets2.3 Federal Specifications:4DD-G-1403 Glass,Plate(Float),Sheet Figured,and Span-drel(Heat Strengthened and Fully Tempered)LP-391 Plastic Sheets,Rods and Tubing,Rigid Cast,Meth-acrylate(Multiapplication)QQ-C-320 Chromium Plating(Electrodeposited)QQ-Z-325 Z
8、inc Coating,Electrodeposited2.4 American National Standard Institute Standards:5ANSI Z97.1-1975 Safety Performance Specifications andMethods of Test for Safety Glazing Material Used inBuildings3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 flush doorsmetal doors with a smooth
9、surface on theexterior face.3.1.2 hinged doordoor equipped with hinges that permit itto swing about the vertical hinge axis,either right hand or lefthand.3.1.2.1 right-hand doordoor with hinges on the right sidewhen viewed from the exterior of the furniture item containingthe door.3.1.2.2 left-hand
10、doordoor with hinges on the left sidewhen viewed from the exterior of the furniture item containingthe door.3.1.3 panel doorsdoors with metal stiles and rails thatsupport a panel insert of transparent safety glazing or expandedaluminum.1This specification is under the jurisdiction of ASTM Committee
11、F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved June 1,2012.Published October 2012.Originallyapproved in 1982.Last previous edition approved in 2007 as F782-01(2007).DOI:10.1520/F0782-01R12.2For refere
12、nced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from the American Institute of Steel Construction,400 N.MichiganAv
13、e.,Chicago,IL 60611.4Available from Standardization Documents Order Desk,Bldg.4 Section D,700Robbins Ave.,Philadelphia,PA 19111-5094,Attn:NPODS.5Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.Copyright ASTM International,100 Ba
14、rr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.1.3.1 stilesthe vertical members in the frame of a paneldoor that support the central panel.3.1.3.2 railsthe horizontal members in the frame of apanel door that support the central panel.4.Classification4.1 Doors shall be o
15、f the following types as required by thespecifications for the item of furniture in which they areinstalled and as indicated in ordering documents.See Fig.1 fordetails.4.1.1 Type IFlush hinged door.4.1.2 Type IIPanel hinged door.5.Ordering Information5.1 Doors are included as part of the orders for
16、items offurniture requiring doors.To describe adequately the door ordoors required,these orders shall include,as necessary,thefollowing information:5.1.1 Type.5.1.2 Size,see Section 8.5.1.3 Paint:5.1.3.1 ColorPer the purchasers requirements.5.1.3.2 Manufacturers standard baked enamel will be fur-nished unless otherwise required and indicated by the pur-chaser.5.1.4 For single-hinged doors,indicate hand if not obviousor if a specific hand is required.5.1.5 Material for Type II(panel)doors may be