ImageVerifierCode 换一换
格式:PDF , 页数:7 ,大小:198.87KB ,
资源ID:190376      下载积分:9 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/190376.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_F_3149_-_15.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_F_3149_-_15.pdf

1、Designation:F314915Standard Practice forDetermining the Maintenance Factor(m)and Yield Factor(y)Loading Constants Applicable to Gasket Materials andDesigns1This standard is issued under the fixed designation F3149;the number immediately following the designation indicates the year oforiginal adoptio

2、n or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice will establish criteria for determiningloading constants that are re

3、ferenced in the American Societyof Mechanical Engineers(ASME)pressure vessel design(Boiler and Pressure Vessel Code,Section VIII,Divs.1 and 2).These constants are specific to this design criterion formetallic,semi-metallic,and nonmetallic gaskets.1.2 UnitsThe values stated in inch-pound units are to

4、 beregarded as the standard.The values given in parentheses aremathematical conversions to SI units that are provided forinformation only and are not considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of

5、the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D2000 Classification System for Rubber Products in Auto-motive ApplicationsF104 Classification System for

6、Nonmetallic Gasket Materi-alsF868 Classification for Laminated Composite Gasket Mate-rials2.2 ASME Standards:3B16.5 Pipe Flanges and Flanged Fittings:NPS 1/2 throughNPS 24 Metric/Inch Standard Boiler and Pressure VesselCode Section VIII,Divs.1 and 2PCC-1 Guidelines for Pressure Boundary Bolted Flang

7、eJoint Assembly2.3 DIN Standard:DIN 3535 Gaskets for Gas Supply42.4 FSA Standard:FSA G 605:11 Standard Test Method for Determining(m)and(y)Loading Constants Applicable to Gasket Materialsand Designs53.Terminology3.1 Definitions:3.1.1 gasket contact area,A1,ngasket area in contact withthe flange surf

8、aces and under load.3.1.1.1 DiscussionThe gasket contact area described inthis practice can deviate from the effective area described in theASME pressure vessel design.3.1.2 leak rate,nvolumetric leak rate per inch gasketoutside diameter.3.1.3 maintenance factor,m,nfactor that is required tocalculat

9、e the additional flange fastener preload needed tomaintain a seal after internal pressure is applied to a joint.3.1.4 surface stress,nstress applied to the gasket contactarea and equal to the applied load divided by gasket contactarea.3.1.5 yield factor,y,nfactor that provides the gasketminimum desi

10、gn seating stress required to seal a joint uponassembly.3.1.5.1 DiscussionThisassumesnopressureand,therefore,a lack of hydrostatic end load effect on the assembly.Reported in psi.4.Significance and Use4.1 The gasket factors are a function of leak rate;therefore,this practice generates curves.Constan

11、ts for use in the ASMEBoiler and Pressure Vessel Code,Section VIII,Appendix 21This practice is under the jurisdiction ofASTM Committee F03 on Gaskets andis the direct responsibility of Subcommittee F03.40 on Chemical Test Methods.Current edition approved June 1,2015.Published August 2015.DOI:10.1520

12、/F3149-15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American Society of Mechanical Engineers

13、(ASME),ASMEInternational Headquarters,Two Park Ave.,New York,NY 10016-5990,http:/www.asme.org.4Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.5Available from the Fluid Sealing Association,994 Old Eagle School Rd.,#1019,Wayne,PA

14、 19087-1866.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 code calculations are selected from these data.Specific m andy values can be selected based on a maximum desired leak rateor derived from these data as described in this procedur

15、e.Thispractice addresses the influence of leak rate and gasketthickness on a gaskets ability to provide a seal initially and inoperation.This practice is performed at room temperature;therefore,this practice does not account for all conditions,suchas high temperature or thermal cycling or both,that

16、boltedflange connections may be subject to in field application.4.2 This practice determines two general characteristics thatare specific to the ASME design criteria.Caution should beexercised when comparing yield and maintenance factorsbetween gasket materials,and it is recommended that the mand y curves be compared.Selecting a gasket material for usein an application should not be based exclusively on these twogeneral characteristics.Gasket material selection for a givenapplication should cons

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2