1、Designation:F176001(Reapproved 2011)Standard Specification forCoextruded Poly(Vinyl Chloride)(PVC)Non-Pressure PlasticPipe Having Reprocessed-Recycled Content1This standard is issued under the fixed designation F1760;the number immediately following the designation indicates the year oforiginal adop
2、tion or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification has been published in response to thespecial circumstance of
3、 regulatory requirements regardingfederal procurement guidelines for plastic pipe having recycledcontent.1.2 This specification covers coextruded Poly(Vinyl Chlo-ride)(PVC)plastic pipe with a center layer and concentricinner and outer solid layers.The pipe is produced using amulti-layer coextrusion
4、die.The inner and outer layers aremade of virgin PVC compound and the center layer hasreprocessed-recycled PVC content.The pipe is for non-pressure use in three series:1.2.1 Sewer-Drain series with a sewer-pipe outside diameterand a pipe stiffness of 46 psi(320 kPa),1.2.2 IPS Schedule 40 series,and1
5、.2.3 IPS Pipe Stiffness(PS)series with pipe stiffnesses of100 psi(690 kPa)and 120 psi(830 kPa).1.3 Pipe that is outside-diameter controlled does not neces-sarily have an inside diameter suitable for use as a fittingsocket.1.4 All series may be perforated.1.5 The values stated in inch-pound units are
6、 to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of t
7、he user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D883 Terminology Relating to PlasticsD1243 Test Method for Dilute Solution Viscosity of VinylChloride Polym
8、ersD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1784 Specification for Rigid Poly(Vinyl Chloride)(PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC)CompoundsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2412 Test Method for Determination of Ex
9、ternal LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D2466 Specification for Poly(Vinyl Chloride)(PVC)PlasticPipe Fittings,Schedule 40D2665 Specification
10、 for Poly(Vinyl Chloride)(PVC)PlasticDrain,Waste,and Vent Pipe and FittingsD2855 Practice for Making Solvent-Cemented Joints withPoly(Vinyl Chloride)(PVC)Pipe and FittingsD3034 Specification for Type PSM Poly(Vinyl Chloride)(PVC)Sewer Pipe and FittingsD3212 Specification for Joints for Drain and Sew
11、er PlasticPipes Using Flexible Elastomeric SealsD4396 Specification for Rigid Poly(Vinyl Chloride)(PVC)and Chlorinated Poly(Vinyl Chloride)(CPVC)Com-pounds for Plastic Pipe and Fittings Used in NonpressureApplications(Withdrawn 2015)3F412 Terminology Relating to Plastic Piping Systems1This specifica
12、tion is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.25 on VinylBased Pipe.Current edition approved Feb.1,2011.Published March 2011.Originallyapproved in 1996.Last previous edition approved in 2005 as F176001(2005)1.DOI:10
13、.1520/F1760-01R11.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical st
14、andard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 F477 Specification for Elastomeric Seals(Gaskets)for Join-ing Plastic PipeF512 Specification for Smooth-Wall Poly(Vinyl Chloride)(PVC)Conduit and Fittings
15、 for Underground InstallationF1336 Specification for Poly(Vinyl Chloride)(PVC)Gas-keted Sewer FittingsF1365 Test Method for Water Infiltration Resistance ofPlastic Underground Conduit Joints Which Use FlexibleElastomeric Seals2.2 Plastic Pipe Institute Technical Report:4PPI-TR-7 Recommended Method f
16、or Calculation of Nomi-nal Weight of Plastic Pipe3.Terminology3.1 Definitions:3.1.1 Definitions are in accordance with TerminologiesD883,D1600,and F412,unless otherwise indicated.3.1.2 coextrusiona process whereby two or more plasticmaterial streams are forced through one or more shapingorifices and become one continuously formed piece.3.2 Definitions of Terms Specific to This Standard:3.2.1 center-layer compoundgeneral description for“in-ternal recycled material”(3.2.5),“external recycled mater