ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:59.01KB ,
资源ID:190552      下载积分:10 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/190552.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM_F_1804_-_08_2012.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

ASTM_F_1804_-_08_2012.pdf

1、Designation:F180408(Reapproved 2012)Standard Practice forDetermining Allowable Tensile Load for Polyethylene(PE)Gas Pipe During Pull-In Installation1This standard is issued under the fixed designation F1804;the number immediately following the designation indicates the year oforiginal adoption or,in

2、 the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice provides a means to determine an allow-able tensile load(ATL)value for a po

3、lyethylene gas pipe thatis to be installed underground using methods that pull the pipeinto a trench(cut or plowed),bore hole,casing pipe,or the like.The ATL value takes into account pipe size,tensile yeildstrength,pipe temperature,and pulling load duration.1.2 The ATL is used to set the break-away

4、strength for a“weak-link”device,or as a limit setting for other devices thatcontrol the maximum pulling force exerted by equipment usedto pull polyethylene gas pipe into an underground location,orto determine if pulling equipment can extert pulling forcegreater than the ATL value for the gas pipe be

5、ing installed.Aweak-link device is installed where the pipe pulling equipmentis connected to the polyethylene gas pipe.If pulling loadexceeds the ATL limit,the device de-couples the pipe from thepulling equipment.Other measures or equipment that limit thepulling force on the pipe are also used.When

6、the ATL value iscompared to the pulling force developed by the pull-in instal-lation equipment and equipment cannot extert pulling forcegreater than the ATL value,a weak-link or other device forlimiting the pulling force is not necessary.1.3 This practice does not address weak-link device designor r

7、equirements,nor does it address the design or requirementsfor other equipment or procedures used to limit the pullingforce applied to polyethylene gas pipe during pull-in installa-tion.1.4 This practice does not address installation methods orprocedures employed for pull-in of polyethylene gas pipe.

8、1.5 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.6 This standard does not purport to address all of thesafety concerns,if any,associa

9、ted with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D638 Test Method for Tensile Properties of PlasticsD1600 Termi

10、nology forAbbreviated Terms Relating to Plas-ticsD2513 Specification for Polyethylene(PE)Gas PressurePipe,Tubing,and FittingsF412 Terminology Relating to Plastic Piping Systems3.Terminology3.1 Unless otherwise indicated,abbreviations are in accor-dance with Terminology D1600,and terms are in accorda

11、ncewith Terminology F412.3.2 allowable tensile load(ATL),nThe maximum tensileload applied to a polyethylene gas pipe during pull-in instal-lation that does not result in an unrecoverable tensile elonga-tion of the pipe.NOTE1Polyethylene gas pipe materials are visco-elastic,that is,theyexhibit proper

12、ties associated with both elastic materials such as rubber,and viscous materials such as wax or clay.When subjected to a tensileload that is significant,but less than the yield strength,polyethylene willelongate or stretch.If the load is then removed,polyethylene will,overtime,recover all or part of

13、 the elongation,depending upon the magnitudeof the load,and the length of time the load was applied.For the purposesof this practice,elongation that is not completely recovered in about 24 hafter the load is released,is considered unrecoverable.4.Significance and Use4.1 The ATL value is used to set

14、the break-away strength ofa weak-link device,or to set other equipment used to limitpulling force during pull-in installation of polyethylene gaspipe,or to determine if pulling equipment can extert pullingforce greater than the ATL value for the polyethylene gas pipebeing installed.1This practice is

15、 under the jurisdiction of Committee F17 on Plastic PipingSystems and is the direct responsibility of Subcommittee F17.60 on Gas.Current edition approved Aug.1,2012.Published October 2012.Originallyapproved in 1997.Last previous edition approved in 2008 as F180408.DOI:10.1520/F1804-08R12.2For refere

16、nced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 4.2 The ATL value is determined before gas pipe installa-tion.5.Procedure5.1 The following information about the polyethylene gaspipe is required:size(outside diameter

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2