1、Designation:F212606(Reapproved 2010)An American National StandardStandard Test Method forTreestand Static Load Capacity1This standard is issued under the fixed designation F2126;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the yea
2、r of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of the staticload capacity of treestands in terms of a factor of safety rela
3、tiveto the manufacturers rated capacity.1.2 The values stated are in inch-pound units and are to beregarded as the standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-p
4、riate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2F2531 Test Method for Load Capacity of Treestand Seats3.Terminology3.1 The terminology and definitions in the referenced docu-ments are applicable to th
5、is test method.3.2 Definitions:3.2.1 backbar or V-baradjustable component of a climb-ing treestand or handclimber that engages the tree to providesupport.The backbar may be rigid or flexible.3.2.2 climbing stickdevice used to assist climbing a treeprimarily to a fixed position treestand.A structure
6、that issecured to the tree and allows the user to support his weightand climb to the desired height on the tree.3.2.3 climbing treestandtreestand that provides both themeans to ascend the tree,and allow the user to remain at adesired elevation.3.2.4 handclimber,or climbing aiddevice to assist climb-
7、ing with a climbing treestand.A structure that allows the userto support his weight when lifting a climbing treestand with hislegs.3.2.5 ladder treestandtreestand that is secured to the treeat the elevation where the platform is located.(The laddertreestand may be secured to the tree at other locati
8、ons and hassteps that are used to reach the platform or hunting position.)3.2.6 non-climbing,fixed position or hang-on treestandtreestand that is secured to the tree at the elevation where it isused.(The user usually ascends the tree by some means andthen lifts the treestand to the desired position
9、and secures it foruse.)3.2.7 platformhorizontal structural area of a treestand onwhich the user stands and/or places his feet.3.2.8 treestanddevice designed to be affixed to a tree or itsbranches so as to permit an individual to sit or stand thereon forthe purpose of attaining an elevated position f
10、rom which toobserve,photograph or hunt.3.2.9 tripod or tower standtripod or tower stand is con-structed to be self-supporting and is not required to be securedto a tree.4.Summary of Test Method4.1 A climbing treestand is mounted so that its platform isperpendicular or slightly above horizontal to a
11、rigid wood ormetal pole when the rated load is applied parallel to themounting pole.A fixed position or ladder treestand shall bemounted with the platform perpendicular to the mounting pole.A tripod stand shall be positioned so that the platform isperpendicular to the application of the load.A climb
12、ing stickshall be mounted such that the steps are perpendicular to thepole.The platform is equipped with deflection measurementdevices.The load is applied step-wise and recordings are madeof the load and deflection at each step until yielding orpermanent deflection occurs or until twice the rated lo
13、ad isapplied.The ladder,tripod and climbing sticks do not requiredeflection measurements be taken.5.Significance and Use5.1 This test method is intended for quality assurance andproduction control purposes.1This test method is under the jurisdiction of ASTM Committee F08 on SportsEquipment,Playing S
14、urfaces,and Facilitiesand is the direct responsibility ofSubcommittee F08.18 on Treestands.Current edition approved May 1,2010.Published May 2010.Originallyapproved in 2001.Last previous edition approved in 2006 as F2126 06.DOI:10.1520/F2126-06R10.2For referenced ASTM standards,visit the ASTM websit
15、e,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.Appara
16、tus6.1 A rigid round wood or metal pole,preferably vertical,isused to mount the subject product such that pole deflection isminimized.6.1.1 The mounting pole diameter shall be 10 in.(254 mm),6 1 in.(25.4 mm).6.2 The load shall be applied using either calibrated weightsor a mechanical device in conjunction with a calibrated loadcell.6.2.1 The use of calibrated weights requires that weightplacement be accurate to assure that the load applicationcentroid is coincident with the boundaries defined an