1、Designation:G9817Standard Test Method forGalling Resistance of Materials1This standard is issued under the fixed designation G98;the number immediately following the designation indicates the year of originaladoption or,in the case of revision,the year of last revision.Anumber in parentheses indicat
2、es the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers a laboratory test which ranksthe galling resistance of material couples.Most galling studieshave been conducted on bare metals and alloys;however
3、,non-metallics,coatings,and surface modified alloys may alsobe evaluated by this test method.1.2 This test method is not designed for evaluating thegalling resistance of material couples sliding under lubricatedconditions because galling usually will not occur under lubri-cated sliding conditions us
4、ing this test method.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health and environmental practices and deter-mine the applicability of regulatory limitati
5、ons prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization Tech
6、nicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2E177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test MethodG83 Test Method for Wear Testing with a Crossed-Cyli
7、nderApparatus(Withdrawn 2005)33.Terminology3.1 Definitions:3.1.1 gallinga form of surface damage arising betweensliding solids,distinguished by macroscopic,usually localized,roughening and creation of protrusions above the originalsurface;it often includes plastic flow or material transfer,orboth.3.
8、1.1.1 DiscussionThe onset of galling usually requiresthat the contact pressure exceeds some threshold value.Gallingcan be a precursor to seizing or loss of function.The identifi-cation of galling is somewhat subjective,and complete agree-ment does not exist,even among experts.3.2 Definitions of Term
9、s Specific to This Standard:3.2.1 threshold galling stressthe stress midway betweenthe highest non-galled stress and the lowest galled stress asdetermined by this test method.4.Summary of Test Method4.1 This test method uses available laboratory equipmentcapable of maintaining a constant,compressive
10、 load betweentwo flat specimens,such as hydraulic or screw feed compres-sion testing machines.One specimen is slowly rotated onerevolution 360 relative to the other specimen.The surfaces areexamined for galling after sliding.The criterion for whethergalling occurs is the appearance of the specimens
11、based onunassisted visual examination.If the specimens have notgalled,a new set of specimens is tested at increased load.Thisprocess is continued until galling occurs.4.2 Appropriate load intervals are chosen to determine thethreshold galling stress within an acceptable range.4.3 The higher the thre
12、shold galling stressing,the moregalling resistant is the test couple.5.Significance and Use5.1 This test method is designed to rank material couples intheir resistance to the failure mode caused by galling and notmerely to classify the surface appearance of sliding surfaces.5.2 This test method shou
13、ld be considered when damaged(galled)surfaces render components non-serviceable.Experi-ence has shown that galling is most prevalent in slidingsystems that are slow moving and operate intermittently.Thegalling and seizure of threaded components is a classicexample which this test method most closely
14、 simulates.1This test method is under the jurisdiction of ASTM Committee G02 on Wearand Erosion and is the direct responsibility of Subcommittee G02.40 on Non-Abrasive Wear.Current edition approved July 15,2017.Published August 2017.Originallyapproved in 1989.Last previous edition approved in 2009 a
15、s G98 02(2009).DOI:10.1520/G0098-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of
16、this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 5.3 Other galling-pron