1、Designation:F67002(Reapproved 2012)An American National StandardStandard Specification forTanks,5 and 10-Gal(20 and 40-L)Lube Oil Dispensing1This standard is issued under the fixed designation F670;the number immediately following the designation indicates the year of originaladoption or,in the case
2、 of revision,the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specificat
3、ion covers the material,dimensions,andconstruction of 5 and 10-gal(20 and 40-L)tanks purchased tostore and dispense lubricating oils.The tanks are industrialsafety cans mounted on a T-bar bracket,complete with driptray.1.2 The values stated in inch-pound units are to be regardedas the standard.The v
4、alues given in parentheses are forinformation only.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of reg
5、ulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelA108 Specification for Steel Bar,Carbon and Alloy,Cold-FinishedA164 Specification for Electrodeposited Coatings of Zinc onSteel;Replaced by B 663(Withdrawn 1981)3A167 Specific
6、ation for Stainless and Heat-ResistingChromium-Nickel Steel Plate,Sheet,and Strip(With-drawn 2014)3A308/A308M Specification for Steel Sheet,Terne(Lead-TinAlloy)Coated by the Hot-Dip ProcessA569/A569M SpecificationforSteel,Carbon(0.15Maximum,Percent),Hot-Rolled Sheet and Strip Commer-cial(Withdrawn 2
7、000)33.Ordering Information3.1 Orders for tanks under this specification shall includethe following:3.1.1 Quantity(number),3.1.2 Size,either 5 or 10 gal(20 or 40 L),3.1.3 Purchase option for finished tank materials:Terneplate(4.1.3),and3.1.4 ASTM designation and year of issue.3.2 If only size,quanti
8、ty,and ASTM designation are speci-fied and no purchase options are specified,then suppliers shallfurnish all stainless steel tanks,brass faucets with flasharrestors,and painted steel mounting columns with bolt-on driptray assemblies,which include perforated steel tray liners,drain plugs,drilled moun
9、ting holes,and mounting bolts.3.3 Optional packaging/shipping.3.3.1 If required for shipping,tanks shall be packagedindividually in cartons suitable for freight handling.4.Materials and Manufacture4.1 Materials:4.1.1 316 Stainless Steel Sheet(Specification A167),mini-mum thickness 24 gage(0.6 mm)on
10、tank body,22 gage(0.8mm)on tank top and bottom;body bracket,filler spout,flasharrestor,vacuum breaker valve and linkage.4.1.2 316 Stainless Steel Cast,Wrought,or Forged Flanges,(for faucet and drain).4.1.3 Terne Plate Sheet(purchase option),minimum thick-ness 22 gage(0.8 mm)on tank body,top and bott
11、om:bodybracket,filler spout(Specification A308/A308M).4.1.4 Mild Steel:4.1.4.1 Bolt-On Column Stand,T-section,hot-rolled(Speci-fication A36/A36M);minimum thickness 0.160 in.(4 mm).4.1.4.2 Drip Tray Bracket,round edge,hot-rolled(Specifi-cation A569/A569M).4.1.4.3 Drip Tray Assembly,hot or cold-rolled
12、(Specifica-tion A108).4.1.4.4 Drip Tray Liner,11-gage(3 mm),zinc-plated(Specification A164).4.1.4.5 Filler Spout Cover,zinc-plated steel(SpecificationA164).4.1.4.6 Drip Tray Drain,34-in.(20 mm)NPS drain.4.1.5 Cast Brass:1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand
13、Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved June 1,2012.Published October 2012.Originallyapproved in 1980.Last previous edition approved in 2007 as F670 02(2007).DOI:10.1520/F0670-02R12.2For referenced ASTM standa
14、rds,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright
15、 ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 DimensionsSizeAHeight,in.BBolt Hole Spacing,in.CTank Height,in.DNumber of Bolt HolesWeight,lbDryWet(Water)5-gal221210129783398110-gal333410122078449132Note 1Dimensions and construction for guidance o
16、nly.Note 21 in.=25.4 mm.Note 31 lb=0.4536 Kg.FIG.1 Dimension of TankF670 02(2012)2 4.1.5.1 Faucet,lever-lock,self-closing,34-in.(20mm)outside diameter,male threaded.44.1.5.2 Drip Tray Drain Plug and Tank Bottom Drain Plug,34-in.(20 mm)NPS.4.1.6 Cast Aluminum,self-closing,spring-action type,one-piece,filler spout cover lever.4.2 ManufactureAll sheet metal seams shall be welded.5.Dimensions and Weight5.1 The dimensions in Fig.1 are recommended nominaldimensions.Weights are estimated and are not cr