1、Designation:F2306/F2306M19Standard Specification for12 to 60 in.300 to 1500 mm Annular Corrugated Profile-Wall Polyethylene(PE)Pipe and Fittings for Gravity-FlowStorm Sewer and Subsurface Drainage Applications1This standard is issued under the fixed designation F2306/F2306M;the number immediately fo
2、llowing the designation indicates the yearof original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification
3、covers requirements and test methodsfor annular,corrugated profile wall polyethylene pipe andfittings with an interior liner.The nominal inside diameterscovered are 12 to 60 in.300 to 1500 mm.1.2 The requirements of this specification are intended toprovide pipe and fittings for underground use for
4、gravity-flowstorm sewer and subsurface drainage systems.NOTE1Pipe and fittings produced in accordance with this specifica-tion shall be installed in compliance with Practice D2321.1.3 This specification covers pipe and fittings with aninterior liner using a corrugated exterior profile(Fig.1).1.4 The
5、 products manufactured under this standard useeither virgin or recycled(post-industrial or post-consumer)materials in accordance with the requirements specified foreach.1.5 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard.Thevalues stated in eac
6、h system may not be exact equivalents;therefore,each system shall be used independently of the other.Combining values from the two systems may result in non-conformance with the standard.1.6 The following precautionary caveat pertains only to thetest method portion,Section 7,of this specification.Th
7、isstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety,health,andenvironmental practices and determine the applicability ofregulatory limitations prior to use.1.7 This inter
8、national standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Comm
9、ittee.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2321 Prac
10、tice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Practice for Determination of the Impact Resistanceof Thermoplastic Pipe and Fi
11、ttings by Means of a Tup(Falling Weight)D3212 Specification for Joints for Drain and Sewer PlasticPipes Using Flexible Elastomeric SealsD3350 Specification for Polyethylene Plastics Pipe and Fit-tings MaterialsD3895 Test Method for Oxidative-Induction Time of Poly-olefins by Differential Scanning Ca
12、lorimetryD4218 Test Method for Determination of Carbon BlackContent in Polyethylene Compounds By the Muffle-Furnace TechniqueD4883 Test Method for Density of Polyethylene by theUltrasound TechniqueD5630 Test Method for Ash Content in PlasticsD7399 Test Method for Determination of the Amount ofPolypr
13、opylene in Polypropylene/Low Density Polyethyl-ene Mixtures Using Infrared SpectrophotometryF412 Terminology Relating to Plastic Piping SystemsF477 Specification for Elastomeric Seals(Gaskets)for Join-ing Plastic Pipe1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPipin
14、g Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.Current edition approved April 1,2019.Published April 2019.Originallyapproved in 2005.Last previous edition approved in 2018 as F2306/F2306M 18.DOI:10.1520/F2306_F2306M-19.2For referenced ASTM standards,visit the ASTM website
15、,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO
16、Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 F2136 Test Method for Notched,Constant Ligament-Stress(NCLS)Test to Determine Slow-Crack-Growth Resis-tance of HDPE Resins or HDPE