1、Designation:F298413Standard Specification forSegmental Panel System for the Grout-in-Place-Liner(GIPL)Rehabilitation Method of Existing Man-Entry Size Sewers,Culverts,and Conduits1This standard is issued under the fixed designation F2984;the number immediately following the designation indicates the
2、 year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers the requirements and testmethods
3、 for the materials,dimensions,workmanship,andfinished quality of injection molded poly vinyl chloride(PVC)profile sections used for the field fabrication of a PVC linerinside existing man-entry size circular and non-circular sewers;circular,non-circular,and box culverts,conduits,and verticalshafts o
4、r manholes having dimensions of 39.4 in.and larger(1000 mm and larger).1.2 The segmental panel system produced under this speci-fication is for non-pressure applications where the PVC liner isinstalled in the existing structure and the annular spacebetween the liner and the existing structure is gro
5、uted with alow viscosity,high strength cementitious grout.1.3 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard.Thevalues stated in each system may not be exact equivalents;therefore,each system shall be used independently of the other.Combining
6、values from the two systems may result in non-conformance with the standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine
7、the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD883 Terminology Relating to PlasticsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1784 Specification for Rigid Poly(Vinyl Chloride)(P
8、VC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC)CompoundsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2152 Test Method for Adequacy of Fusion of ExtrudedPoly(Vinyl Chloride)(PVC)Pipe and Molded Fittings byAcetone ImmersionF412 Terminology Relating to Plasti
9、c Piping SystemsG195 Guide for Conducting Wear Tests Using a RotaryPlatform Abraser3.Terminology3.1 GeneralDefinitions are in accordance with Terminol-ogy D883 and Terminology F412.Abbreviations are in accor-dance with Terminology D1600,unless otherwise indicated.3.2 Definitions of Terms Specific to
10、 This Standard:3.2.1 See Fig.1 to clarify terminology.3.2.2 PVC liner,na tubular assembly field fabricated frominjection molded PVC profile wall segments which are as-sembled into rings which are subsequently joined togetherwhich substantially conforms to the shape of the inner surfaceof the existin
11、g pipe structure or conduit over some portion ofor its entire inner circumference.3.2.3 PVC segmental panels,nan element available invarious geometries,consisting of a smooth inner surface and aribbed outer surface(profile)with edge configurations to allowmechanical locking and sealing with adjacent
12、 panels.4.Materials and Manufacture4.1 The molded panel segments shall be made from a PVCcompound meeting all of the requirements for a cell classifi-cation of 12344 or higher as defined in Specification D1784.4.2 The sealant material shall be a polyurethane,mono-liquid,moisture setting type flexibl
13、e gasket that can be appliedto the grooved mating faces of the segmental pieces prior toassembly.4.3 The connecting hardware(connecting screw rods,nuts,and bolts)shall be made of a low carbon,general purpose steel1This test method is under the jurisdiction of ASTM Committee F17 on PlasticPiping Syst
14、ems and is the direct responsibility of Subcommittee F17.67 onTrenchless Plastic Pipeline Technology.Current edition approved Dec.1,2013.Published January 2014.DOI:10.1520/F2984-13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.F
15、or Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 meeting the SAE designation 1020 that has uni-chrome platingapplied,or equi
16、valent.4.4 Rework MaterialClean rework PVC material gener-ated from the manufacturers own production process may beused in the processing of new pieces provided that the finishedproduct meets all the requirements of this specification.5.Other Requirements5.1 Abrasion ResistanceThe resistance to abrasion of thefinished panel materials shall be equivalent to or exceeding thatof other PVC sewer pipeline specifications for applications insanitary and storm sewer systems.In lieu of no abrasionperform