1、Information technology UPnP Device Architecture Part 7-11:Lighting Device Control Protocol Switch Power ServiceTechnologies de linformation Architecture de dispositif UPnP Partie 7-11:Protocole de contrle de dispositif dclairage Service de changement dalimentationINTERNATIONAL STANDARDISO/IEC 29341-
2、7-11Reference numberISO/IEC 29341-7-11:2015(E)Second edition2015-06-15 ISO/IEC 2015 ii ISO/IEC 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO/IEC 2015All rights reserved.Unless otherwise specified,no part of this publication may be reproduced or utilized otherwise in any form or by any mea
3、ns,electronic or mechanical,including photocopying,or posting on the internet or an intranet,without prior written permission.Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel.
4、+41 22 749 01 11Fax+41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandISO/IEC 29341-7-11:2015(E)ISO/IEC 29341-7-11:2015(E)ISO/IEC 2015 All rights reserved iii CONTENTS Foreword.iv Introduction.v 1.Scope.1 2.Service Modeling Definitions.2 2.1.ServiceType.2 2.2.State Variabl
5、es.2 2.2.1.Target.2 2.2.2.Status.2 2.3.Eventing and Moderation.3 2.4.Actions.3 2.4.1.SetTarget.3 2.4.2.GetTarget.4 2.4.3.GetStatus.4 2.4.4.Non-Standard Actions Implemented by a UPnP Vendor.5 2.4.5.Common Error Codes.5 2.5.Theory of Operation.6 3.XML Service Description.7 4.Test.8 LIST OF TABLES Tabl
6、e 2-1:State Variables.2Table 2-2:Event Moderation.3Table 2-3:Actions.3Table 2-4:Arguments for SetTarget.3Table 2-5:Error Codes for SetTarget.4Table 2-6:Arguments for GetTarget.4Table 2-7:Error Codes for GetTarget.4Table 2-8:Arguments for GetStatus.4Table 2-9:Error Codes for GetStatus.5Table 2-10:Com
7、mon Error Codes.5 ISO/IEC 29341-7-11:2015(E)iv ISO/IEC 2015 All rights reserved Foreword ISO(the International Organization for Standardization)and IEC(the International Electrotechnical Commission)form the specialized system for worldwide standardization.National bodies that are members of ISO or I
8、EC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity.ISO and IEC technical committees collaborate in fields of mutual interest.Other international organizations,govern
9、mental and non-governmental,in liaison with ISO and IEC,also take part in the work.In the field of information technology,ISO and IEC have established a joint technical committee,ISO/IEC JTC 1.The procedures used to develop this document and those intended for its further maintenance are described i
10、n the ISO/IEC Directives,Part 1.In particular the different approval criteria needed for the different types of document should be noted.This document was drafted in accordance with the editorial rules of the ISO/IEC Directives,Part 2(see http:/www.iso.org/directives).Attention is drawn to the possi
11、bility that some of the elements of this document may be the subject of patent rights.ISO and IEC shall not be held responsible for identifying any or all such patent rights.Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO l
12、ist of patent declarations received(see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of the ISO specific terms and expressions related to conformity assessment,as w
13、ell as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade(TBT)see the following URL:Foreword Supplementary information ISO/IEC 29341-7-11 was prepared by UPnP Implementers Corporation and adopted,under the PAS procedure,by joint technical committee ISO/IEC JTC
14、1.Information technology,in parallel with its approval by national bodies of ISO and IEC.This second edition replaces the first edition(ISO/IEC 29341-7-11:2008),which has been technically revised.The list of all currently available parts of ISO/IEC 29341 series,under the general title Information te
15、chnology UPnP Device Architecture,can be found on the ISO web site.ISO/IEC 29341-7-11:2015(E)ISO/IEC 2015 All rights reserved v Introduction ISO and IEC draw attention to the fact that it is claimed that compliance with this document may involve the use of patents as indicated below.ISO and IEC take
16、 no position concerning the evidence,validity and scope of these patent rights.The holders of-these patent rights have assured ISO and IEC that they are willing to negotiate licenses under reasonable and non-discriminatory terms and conditions with applicants throughout the world.In this respect,the statements of the holders of these patent rights are registered with ISO and IEC.Intel Corporation has informed ISO and IEC that it has patent applications or granted patents.Information may be obtai