ImageVerifierCode 换一换
格式:PDF , 页数:7 ,大小:663.33KB ,
资源ID:468812      下载积分:10 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。 如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【https://www.wnwk.com/docdown/468812.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: QQ登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(BS_3735-1987.pdf)为本站会员(益****师)主动上传,蜗牛文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知蜗牛文库(发送邮件至admin@wnwk.com或直接QQ联系客服),我们立即给予删除!

BS_3735-1987.pdf

1、BS3735:1987ForewordThis British Standard has been prepared under the direction of the BuildingServices Standards Committee.It is a revision of BS 3735:1976,which iswithdrawn.The principal changes in this revision are as follows.a)The scope of the standard now covers both rubber and plastics lids but

2、 nolonger covers rubber foot rings.b)There is no longer a requirement for resistance to weathering.c)The requirement for the mass of lids has been simplified.For information on low carbon steel dustbins and lids see BS 792.A British Standard does not purport to include all the necessary provisions o

3、f acontract.Users of British Standards are responsible for their correct applicationCompliance with a British Standard does not of itself confer immunityfrom legal obligations.Summary of pagesThis document comprises a front cover,an inside front cover,pages i and ii,pages 1 and 2,an inside back cove

4、r and a back cover.This standard has been updated(see copyright date)and may have hadamendments incorporated.This will be indicated in the amendment table on theinside front cover.BSI11-1999BS3735:19871 Scope6.2 The lid shall be provided with either:盈This British Standard specifies requirements fora

5、)a handle having a grip of not less than 80 mmdustbin lids manufactured from polymericin length with a clear unobstructed projection ofcompounds of thermoplastics or rubber or anot less than 25 mm,the gripping part of which.云ocombination of both,suitable for use with dustbinsshall be radiused all ro

6、und to eliminate sharpwhich comply with BS 4998 or,in the case of lowcorners or edges:orcarbon(mild steel)dustbins,which comply withb)a handle having a length of not lessBS792.than 80 mm and a solid projection of not lessNOTE The titles of the publications referred to in this standardthan 25 mm.are

7、listed on the inside back cover.Where the lid is designed to lift off the bin,the2 Definitionsgrip/handle shall be centrally situated.6.3 The lid top shall be convex with no cavitiesFor the purposes of this British Standard,thewhich would prevent the drainage of water.The lidfollowing definitions ap

8、ply.shall be so designed as to remain secure when the2.1dustbin is tilted at an angle of 45,without the20:004thermoplasticsassistance of attachments or clips.Where the lida plastics material capable of being repeatablyenters or overlaps the bin body for which it issoftened by heat and hardened by co

9、olingdesigned it shall have a minimum entry or overlapheight of 30 mm,with a maximum radial clearance2.2of 10 mm diametral.rubbera solid material with elastic properties made from7 Performancelatex from living plants or synthetically7.1 Impact strength莒3 ClassificationWhen tested in accordance with

10、the method8described in Appendix A,the lid shall show noThermoplastics and rubber dustbin lids aresplitting.Subsequent to this test the lid shall meetclassified as follows:the requirements specified in 6.3.Type 1:clipped lid;7.2 Deformation resistance8品Type 2:unclipped lid;When tested in accordance

11、with the methodType 3:heavy duty.described in Appendix B,the lid shall show nosplitting or permanent deformation.Subsequent to4 Materialthis test the lid shall meet the requirementsThe material from which the lid is produced shall bespecified in 6.3.a polymeric compound of thermoplastics or rubberor

12、 a combination of both.8 MarkingEach lid shall be clearly and permanently marked5 Masswith the following:The minimum mass of the lid shall be:a)number and date of this British Standard,Type 1:0.50 kg;i.e.BS3735:1987:需Type 2:0.55 kg;b)size(diameter)and type of lid;Type 3:2.00 kg.c)manufacturers name

13、and identificationNOTE Unless otherwise specified,the lid should be clearly and6 Design requirementspermanently marked with the wordingNO HOT ASHES.品6.1 The lid shall be round with both the inside andoutside surfaces smooth and free from flashes andshall have no sharp edges.1)Marking BS 3735:1987 on

14、 or in relation to a product is a claim by the manufacturer that the product has been manufactured tothe requirements of the standard.The accuracy of such a claim is therefore solely the manufacturers responsibility.Enquiries asto the availability of third party certification should be addressed to the appropriate certification body.BSI11-1999

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2