1、Running Tools,Pulling Tools,and Kick-over Tools and Latches for Side-pocket MandrelsANSI/API SPECIFICATION 19G3FIRST EDITION,JUNE 2011CONTAINS API MONOGRAM ANNEX AS PART OF U.S.NATIONAL ADOPTIONREAFFIRMED,JUNE 2019ISO 17078-3:2009(Identical),Petroleum and natural gas industriesDrilling and productio
2、n equipment,Part 3Running tools,pulling tools,and kick-over tools and latches for side-pocket mandrelsRunning Tools,Pulling Tools,and Kick-over Tools and Latches forSide-pocket MandrelsUpstream SegmentANSI/API SPECIFICATION 19G3FIRST EDITION,JUNE 2011CONTAINS API MONOGRAM ANNEX AS PART OF U.S.NATION
3、AL ADOPTIONREAFFIRMED,JUNE 2019ISO 17078-3:2009(Identical),Petroleum and natural gas industriesDrilling and production equipment,Part 3Running tools,pulling tools,and kick-over tools and latches for side-pocket mandrelsSpecial NotesAPI publications necessarily address problems of a general nature.Wi
4、th respect to particular circumstances,local,state,and federal laws and regulations should be reviewed.Neither API nor any of APIs employees,subcontractors,consultants,committees,or other assignees make anywarranty or representation,either express or implied,with respect to the accuracy,completeness
5、,or usefulness of theinformation contained herein,or assume any liability or responsibility for any use,or the results of such use,of anyinformation or process disclosed in this publication.Neither API nor any of APIs employees,subcontractors,consultants,or other assignees represent that use of this
6、 publication would not infringe upon privately owned rights.API publications may be used by anyone desiring to do so.Every effort has been made by the Institute to assure theaccuracy and reliability of the data contained in them;however,the Institute makes no representation,warranty,orguarantee in c
7、onnection with this publication and hereby expressly disclaims any liability or responsibility for loss ordamage resulting from its use or for the violation of any authorities having jurisdiction with which this publication mayconflict.API publications are published to facilitate the broad availabil
8、ity of proven,sound engineering and operatingpractices.These publications are not intended to obviate the need for applying sound engineering judgmentregarding when and where these publications should be utilized.The formulation and publication of API publicationsis not intended in any way to inhibi
9、t anyone from using any other practices.Any manufacturer marking equipment or materials in conformance with the marking requirements of an API standardis solely responsible for complying with all the applicable requirements of that standard.API does not represent,warrant,or guarantee that such produ
10、cts do in fact conform to the applicable API standard.All rights reserved.No part of this work may be reproduced,translated,stored in a retrieval system,or transmitted by any means,electronic,mechanical,photocopying,recording,or otherwise,without prior written permission from the publisher.Contact t
11、he Publisher,API Publishing Services,200 Massachusetts Avenue,NW,Suite 1100,Washington,DC 20001.Copyright 2011 American Petroleum InstituteAPI ForewordNothing contained in any API publication is to be construed as granting any right,by implication or otherwise,for themanufacture,sale,or use of any m
12、ethod,apparatus,or product covered by letters patent.Neither should anythingcontained in the publication be construed as insuring anyone against liability for infringement of letters patent.Shall:As used in a standard,“shall”denotes a minimum requirement in order to conform to the specification.Shou
13、ld:As used in a standard,“should”denotes a recommendation or that which is advised but not required in orderto conform to the specification.This document was produced under API standardization procedures that ensure appropriate notification and participation in the developmental process and is desig
14、nated as an API standard.Questions concerning the interpretation of the content of this publication or comments and questions concerning the procedures under which this publication was developed should be directed in writing to the Director of Standards,American Petroleum Institute,200 Massachusetts
15、 Avenue,NW,Suite 1100,Washington,DC 20001.Requests for permission to reproduce or translate all or any part of the material published herein should also be addressed to the director.Generally,API standards are reviewed and revised,reaffirmed,or withdrawn at least every five years.A one-time extensio
16、n of up to two years may be added to this review cycle.Status of the publication can be ascertained from the API Standards Department,telephone(202)682-8000.A catalog of API publications and materials is published annually by API,200 Massachusetts Avenue,NW,Suite 1100,Washington,DC 20001.Suggested revisions are invited and should be submitted to the Standards Department,API,200 Massachusetts Avenue,NW,Suite 1100,Washington,DC 20001,standardsapi.org.iiiiiiContents PageAPI Foreword.ii Foreword.iv
