1、A M E R I C A N N A T I O.N A L.S T A N D A R D Buttress Inch Screw Threads 7y45 Form With 0.6 Pitch Basic Height of Thread Engagement ANSI B1.9-1973 REAFFIRMED 1992 FOR CURRENT COMMITTEE PERSONNEL REAFFIRMED 1985 PLEASE SEE ASME MANUAL AS-1 1 SECRE TARIA T THE AMERICAN SOCIETY OF MECHANICAL ENGINEE
2、RS PUBLISHED BY T H E A M E R I C A N S O C I E T Y OF M E C H A N l C A L E N G I N E E R S United Engineering Center 345 East 47th Street New York,N.Y.10017 Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further
3、 reproduction or distribution is permitted.Uncontrolled when printed.REAFFIRMED 2001FOR CURRENT COMMITTEE PERSONNELPLEASE E-MAIL CSasme.orgANSI B1.9-1973(R1979)25 May 1983 ACCEPTANCE NOTICE The above non-Government document was adopted on 25 May 1983 and is approved for use by the Federal Agencies.T
4、he indicated industry group has furnished the clearance required by existing regulations.Copies of the document are stocked by the DoD Single Stock Point,Naval Publications and Forms Center,Philadelphia,PA 19120,for issue to DoD activities only.Contractors and industry groups must obtain copies dire
5、ctly from:The American Society of Mechanical Engineers United Engineering Center,345 East 47th Street New York,NY 10017 or The American National Standards Institute,1430 Broadway,New York,NY 10018 Title of Document:Buttress Inch Screw Threads Date of Specific Issue Adopted:22 October 1973 with Errat
6、a,February 1979 Releasing Industry Group:The American Society of Mechanical Engineers NOTICE:The Federal agencies use of this standard is subject to a l l the requirements and limitations of FED-STD-H28/14 Screw-Thread Standards for Federal Services Section 14,Buttress Screw Threads-7O/45O Flank Ang
7、les.NOTICE:When reaffirmation,amendment,revision,or cancellation of this standard is initially proposed,the industry group responsible for this standard,shall inform the military coordinating activity of the proposed change and request participation.Custodians:.Army-AR Navy-As Air Force-11 Review Ac
8、tivities:Army-AT,AV,MI Air Force-15,80,82,99 User Activity:Navy-EC Civil Agency Coordinating Activities:Commerce-NBS DOT-AAF,ACO,FAA,FRA,NHT GSA-FSS,PCD HUD-HCC Justice-FPI NASA-JFK,LRC,MSF USDA-AFS Military Coordinating Activity:DLA-IS(Project THDS-004 1)No part of this document may be reproduced i
9、n any form,in an electronic retrieval system or otherwise,without the prior written permis-sion of the publisher.Incorporates 2/79 Errata Copyright 0 1974 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS Printed in U.S.A.Copyrighted material licensed to Stanford University by Thomson Scientific(),dow
10、nloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.FOREWORD Although the buttress thread was described as early as the March,1888,Journal of the Franklin In-stitute,it was so little used that its national standardization
11、was not undertaken until after the Combined Conservation Committee in early 1942 reviewed the standardization status of items needed in the war ef-fort.Formerly each application of the buttress thread was treated individually and the form it took de-pended on the experience of the designer and the m
12、anufacturing equipment available.At the American-British-Canadian conference in New York,in 1943,they agreed that a basic profile should be established for this thread.As the Military Departments needed buttress and other special types of threads,the War Production Board in February,1944,arranged wi
13、th the ASA to establish a General War Committee on Screw Threads.The Interdepartmental Screw Thread Committee(ISTC)agreed to develop a buttress thread form having a pressure flank angle of 7 deg,which closely approaches the static angle of friction for well lubri-cated steel surfaces in contact,and
14、a clearance flank angle of 45 deg.The British agreed to prepare and circulate a draft specification for an asymmetrical buttress thread having a 7 deg load flank angle,a 45 deg clearance flank angle,and a basic height of thread engagement of 0.4 pitch.The 1944 edition of Handbook H28 published the I
15、STCs recommendation of a basic buttress thread form whch had a crest flat in the nut twice that of the screw,and a thread engagement height of approxi-mately 0.56.In November 1944,the ASA War Subcommittee on Buttress Threads was established and after reviewing the British draft of April 1945,this co
16、mmittee felt that because of the distortion tendency of thn wall tubing,a greater basic height of thread engagement than 0.4 was desirable,especially since the minimum height of thread engagement is necessarily less than 0.4 by one-half the sum of the allowance and the tolerances on minor diameter of internal thread and major diameter of external thread.Therefore,the July 1945 draft of the War Standard was based on a basic height of thread engagement of 0.5.Another American-British-Canadian conf
