1、 ASME BL07=9M 94 m 0759670 0570375 7T5 m Errata to ASME Bl07.9M-1994 The Errata corrections listed below apply to ASME B107.9M-1994,Wrenches,Box,Angled,Open End,Combination,Flare Nut,and Tappet(Metric Series).This Errata is being issued in the form of replacement pages.Corrections are incorporated d
2、irectly into the affected pages.Replace or insert the pages listed.It is also advisable that this cover page be retained for reference.The pages show the corrections given below.The pages not listed are the reverse sides of the listed pages and contain no changes.Page Location Change viii Contents 4
3、 JANUARY 1996 3 Fig.I Fig.6 Fig.7 Fig.8 4.14 Title oJTable I OB corrected to read Type VI,Style 1,Angle Wrench,Double Head,Open End,15 deg.and 60 deg.In thirdparagraph B107.17M corrected to read B107.17M-1991 In top sketch:(I)R2 added to upper left-hand arrow(2)Callout added to upper portion o f rig
4、ht-hand(3)In lower left,30 deg.corrected to read 30(4)In lower right,callouts RI=Flash arc permissible and R2=No flash added In bottom sketch:(I)In lower lep,30 deg.corrected to read 30 Word or added to arrows between two bottom sketches 8 f 5 deg.corrected to read Theta(O)f 5 deg.B f 5 deg.correcte
5、d to read Theta(e)f 5 deg.First sentence corrected to read The wrench shall have two open ends inclined from the wrench handle.THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS 345 East 47th Street,New York,NY 10017 N8794E COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling
6、 ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesPage Location 596 5.2.2 8 17 5.2.3.1 Table 2 Table 10B Change Fourth sentence corrected to read Mandrels shall be hardened to show a hardness of not less than 55 HRC and smoothly finished on the wrenc
7、h engaging surfaces.In the jjh line,gauge corrected to read gage In sixth main column(Height to Where Ogset Blends With Handle),under column E,Small Head,Max.corrected to read Min.Title corrected to read T y p e VI,Style 1,Angle Wrench,Double Head,Open End,15 deg.and 60 deg.COPYRIGHT American Societ
8、y of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling Services标准分享网 w w w.b z f x w.c o m 免费下载CONTENTS Foreword.Standards Committee Roster.1 Scope.2 Classification.3 Applicable Standards.4 Requirements.4.1
9、 Illustrations.4.2 Materials.4.3 Markings.4.4 Hardness.4.5 Proof Loads.4.6 Wrench Opening.4.7 Finish.4.9 Type I.Box Wrench.Double Head.4.10 Type II.Engineers Wrench.Double Head.Open End 15 deg.4.11 Type III.Combination Wrench.Open End.and 15 deg.,Offset Box Openings.4.12 Type IV.Flare Nut Wrench.Dou
10、ble Head.4.13 Type V.Flare Nut Combination Wrench.Open End.and 15 deg.Offset Box Openings.4.14 Type VI.Angle Wrench.Double Head.Open End.4.15 Type VII.Tappet Wrench.Open End.4.16 Workmanship.5 Test Procedures.5.1 Hardness.5.2 Proof Test.4.8 Design.6 Designations.Fig ur es 1 Finish Requirements.2A Ty
11、pe I.Class 1.Style 1 Box Wrench.Double Head.15 deg.Offset Each End.Regular Length.2B Type I.Class 1.Style 1 Box Wrench.Double Head.15 deg.Offset Each End.Regular Length.3 Type I.Class 2.Style 1 and 2 Box Wrench.Double End.Deep Offset Each 4 Type I.Class 2.Style 1 and 2 Box Wrench.Modified Offset.Reg
12、ular and Short Lengths.5 End.Regular and Short Lengths.Type II.Engineers Wrench.Double Head.Open End.15 deg.vii.111 V 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 4 4 4 4 4 5 5 5 6 3 3 3 3 3 4 COPYRIGHT American Society of Mechanical EngineersLicensed by Information Handling ServicesCOPYRIGHT American Society of M
13、echanical EngineersLicensed by Information Handling Services6 Type III.Style 1.2.and 3 Combination Wrench.Open End.and 15 deg.Offset Box Opening.7 Type IV.Flare Nut Wrench.Double Head.8 Type V.Flare Nut Combination Wrench.Open End.and 15 deg.Offset Box Opening.9 Type VI.Style 1.Angle Wrench.Double H
14、ead.Open End.15 deg.and 60 deg.Heads.10 Type VI.Style 2.Angle Wrench.Double Head.Open End.30 deg.and 60 deg.Heads.11 Type VII.Class 1.Tappet Wrench.Double Head.Open End 15 deg.Head.Tables 1 Type I.Class 1.Style 1.Box Wrench.Double Head.15 deg.Offset Each 2 Type I.Class 2.Style 1.Box Wrench.Double He
15、ad.Deep Offset Each 3 Type I.Class 2.Style 2.Box Wrench.Double Head.Deep Offset Each 4 Type I.Class 2.Style 1.Box Wrench.Double Head.Modified Offset.Regular Length.5 Type I.Class 2.Style 2.Box Wrench.Double Head.Modified Offset.Each 6 Type II.Engineers Wrench.Double Head.Open End.15 deg.7A Type III.
16、Style 1.Combination Wrench.Open End and 15 deg.Offset Box 7B Type III.Style 2.Combination Wrench.Open End.15 deg.Offset Box 7C Type III.Style 3.Combination Wrench.Open End.15 deg.Offset Box 8 Type IV.Flare Nut Wrench.Double Head.9 Type V.Flare Nut Combination Wrench.Open End.and 15 deg.Offset Box 10A Type VI.Style 1 and 2.Angle Wrench.Double Head.Open End.10B Type VI.Style 1.Angle Wrench.Double Head.Open End.15 deg.and 60 11 Type Vil.Class 1.Tappet Wrench.Double Head.Open End.15 deg.12 Hexagon M
