1、AMERICAN NATIONAL S T A N D A R D Metric Hex Flange Nuts ANSI B18.2.4.4M-1982 Government Key Words:Nut,Flange,Hex-Metric FOR CURRENT COMMITTEE PERSONNEL PLEASE SEE ASME MANUAL AS-11 SECRETARIAT SOCIETY OF AUTOMOTIVE ENGINEERS THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLISHED B Y T H E A M E R I
2、 C A N S O C I E T Y OF M E C H A N I C A L E N G I N E E R S United Engineering Center 345 East 47th Street New York,N.Y.10017 Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution i
3、s permitted.Uncontrolled when printed.Date of Issuance:October 31,1982 This code or standard was developed under procedures accredited as meeting the criteria for American National Standards.The Consensus Committee that approved the code or standard was bal-anced to assure that individuals from comp
4、etent and concerned interests have had an opportunity to participate.The proposed code or standard was made available to public review and comment which provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not approve,rate,o
5、r endorse any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in con-nection with any items mentioned in this document,and does not undertake to ensure anyone utilizing a standard against liability for infrin
6、gement of any applicable Letters Patent,nor assume any such liability.Users of a code or standard are expressly advised that determination of the validity of any such patent rights,and the risk of infringement of such rights,is entirely their own responsibility.Participation by federal agency repres
7、entative(s)or person(s)affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.Copyrigh
8、t 1982 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in U.S.A.Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printe
9、d.American National Standards Committee B18 for the standardization of bolts,screws,nuts,rivets and similar fasteners was organized in March 1922,as Sectional Committee B18 under the aegis of the American Engineering Standards Committee(later the American Standards Association,then the United States
10、 of America Standards Institute and,as of October 6,1969,the American National Standards Institute,Inc.),with the Society of Automotive Engineers and the American Society of Mechanical Engineers as joint sponsors.Subcommittee 2 was subsequently established and charged with the responsibility for tec
11、hnical content of standards covering wrench head bolts and nuts.At its meeting on December 4,1974,Committee B18 authorized preparation of a series of standards for metric fasteners.Subcommittee 2 was assigned responsibility for developing standards for metric hex bolts,screws and nuts.At a meeting o
12、n September 22,1976,Subcommittee 2 organized the contents of a standard covering six different styles of hex nuts.Actual drafting was postponed until ISO/TC2 could reach final decisions relating to basic dimensions and characteristics of hex bolts,screws and nuts.At ISO/TC2 meetings held in April 19
13、77,final actions were taken,Committee B18 affirmed the TC2 decisions at a meeting on June 29,1977,and drafting of this Standard was started.In February 1978,Committee B18 established a cooperative program with the Department of Defense to draft American National Standards for metric fasteners in suc
14、h a way that they could be used directly by the Government for procurement purposes.The Department of Defense requested that each of the six nut products be covered in separate standards,and Subcommittee 2 accepted this approach at its meeting on June 27,1978.This Standard was approved by letter bal
15、lot of Committee B18 on November 25,1980,and was sub-sequently approved by the secretariat and submitted to the American National Standards Institute for designation as an American National Standard.This was granted on June 21,1982.iii Copyrighted material licensed to Stanford University by Thomson
16、Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.AMERICAN NATIONAL STANDARDS COMMITTEE B18 STANDARDIZATION OF BOLTS,NUTS,RIVETS,SCREWS,WASHERS,AND SIMILAR FASTENERS(The following is the roster at the time of approval of this Standard)OFFICERS J.0.Levy,Chairman H.W.Ellison,Vice-Chairman E.Schwartz.Vice-chairman H.G.Muenchinger,Vice-chairman R.McGinnis,Secretary COMMITTEE PERSONNEL AMERICAN CHAIN ASSOC
