1、M-2 O D 9009275 0024329 541 D/Y)-25-30 A M E R I C A N N A T I O N A L S T A N D A R D Carbide-Tipped Masonry Drills and Blanks for Carbide-Tipped Masonry Drills ANSI B94.12-1977(REVISION OF ANSI 894.12-19681 SKREIARIAT THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLISHED BY T H E A M E R I C A N
2、S O C I E T Y O F M E C H A N I C A L E N G I N E E R S United Engineering Center New York,N.Y.1 O01 7 345 East 47th Street Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:46:29 MSTNo repr
3、oduction or networking permitted without license from IHS-,-,-W 9009275 0024330 263 D No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the pub1 isher.Copyriqht O 1978 by THE AMERICAN SOCIETY OF MECHANICAL EN
4、GINEERS All Rights Reserved Printed in U.S.A.Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:46:29 MSTNo reproduction or networking permitted without license from IHS-,-,-9009275 0024L3L L
5、TT FOREWORD The material contained i n this standard was developed by the Standards Committee of the Cemented Carbide Producers Association after a thorough investigation of the factors involved in the field of carbide-tipped masonry drills and blanks for carbide-tipped masonry drills.It is based on
6、 sound engineering prac-tice and reflects the requirements of the industry.The committee developed three drafts on the subject,each of which was reviewed by interested parties and revised to incorporate the changes suggested.The final draft was submitted to the American Standards Association(later c
7、hanged to USA Standards Institute)and approved as American Standard under the Existing Standards Method on June 22,1962,as B82.1.In 1966 a revision was submitted to and approved by TCI,Carbide and Oxide Tools,of USA Standards Committee B94,Cutting Tools,Holders,Drivers and Bushings.It was later appr
8、oved by the USA Standards Committee B94 and the sponsor.The standard was approved by the USA Standards institute and redesig-nated B94.12 on March 28,1968.Technical Committee 1 drafted another revision to the standard,further updating it to meet current industry practices.This revision was approved
9、as an American National Standard on September 7,1977.iii A-3 Copyright ASME International Provided by IHS under license with ASME Licensee=University of Alberta/5966844001,User=trert,rtyrtyrtyNot for Resale,03/07/2015 23:46:29 MSTNo reproduction or networking permitted without license from IHS-,-,-=
10、9009275 0024332 O36 AMERICAN NATIONAL STANDARDS COMMITTEE B94 Standardization of Cutting Tools,Holders,Drivers and Bushings OFFICERS Harry McLinden,Chairman A.H.Mezey,Vice-chairman Christopher L.Dour,Secretary AMERICAN GEAR MANUFACTURERS ASSOCIATION,THE P.M.Dean,Jr.,Mechanical Technology,Inc.,Latham
11、,New York G.L.Scott,Alternate,American Gear Manufacturers Association,Washington,D.C.M.E.Merchant,Dr.,Cincinnati Milacron,Inc.,Cincinnati,Ohio G.M.Monacelli,General Electric Company,Detroit,Michigan C J.Oxford,Jr.,National Twist Drill&Tool Company,Rochester,Michigan G.F.Wilson,Alternate,Wheeling,Ill
12、inois CEMENTED CARBIDE PRODUCERS ASSOCIATION AMERICAN SOCIETY OF MECHANICAL ENGINEERS,THE J.A.Woodward,Teledyne Firth Sterling,Pittsburgh,Pennsylvania A P.Wherry,Alternate,Cemented Carbide Producers Association,Cleveland,Ohio CUTTING TOOL MANUFACTURERS ASSOCIATION E.J.Czoper,Gorham Tool Industry,Inc
13、.,Detroit,Michigan C W.Jatho,Alternate,Cutting Tool Manufacturers Association,Birmingham,Michigan.GENERAL SERVICES ADMINISTRATION W.R.Wacker,General Services Administration,Washington,D.C.HACK AND BAND SAW MANUFACTURERS ASSOCIATION OF AMERICA Richard Schrade,Clemson Brothers Inc.,Middletown,New York
14、 C M.Stockinger,Alternate,Hack&Band Saw Manufacturers Association of America,Cleveland,Ohio METAL CUTTING TOOL INSTITUTE W.A.Wagner,Cleveland Twist Drill Company,Cleveland,O h i o R.M.Byrne,Alternate,Metal Cutting Tool Institute,New York,New York R.E.Smith,Dayton Progress Corporation,Dayton Ohio NAT
15、IONAL ASSOCIATION OF PUNCH MANUFACTURERS NATIONAL BUREAU OF STANDARDS J.R.Pidgeon,National Bureau of Standards,Washington,D.C.G.F.Wilson,General Electric Company,Worthington,Ohio E.J.Loeffler,Alternate,National Machine Tool Builders Association,McLean,Virginia NATIONAL MACHINE TOOL BUILDERS ASSOCIAT
16、ION SOCIETY OF CARBIDE ENGINEERS C.H.Lang,c/o Society of Carbide Engineers,Bridgeville,Pennsylvania K.A.Lundell,The Producto Machine Company,Jamestown,New York Harry&Linden,Caterpillar Tractor Company,Peoria,Illinois W.N.Moore,The Ford Motor Company,Dearborn,Michigan R.A.Agnew,Western Electric Company,Inc.,Chicago,Illinois S.P.Rogacki,Alternate,Western Electric Co.,Inc,Kearney,New Jersey SOCIETY OF MANUFACTURING ENGINEERS TELEPHONE GROUP,THE iv Copyright ASME International Provided by IHS under
