收藏 分享(赏)

1983_2018.pdf

上传人:益****师 文档编号:167590 上传时间:2023-03-03 格式:PDF 页数:27 大小:2.32MB
下载 相关 举报
1983_2018.pdf_第1页
第1页 / 共27页
1983_2018.pdf_第2页
第2页 / 共27页
1983_2018.pdf_第3页
第3页 / 共27页
1983_2018.pdf_第4页
第4页 / 共27页
1983_2018.pdf_第5页
第5页 / 共27页
1983_2018.pdf_第6页
第6页 / 共27页
亲,该文档总共27页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、AN AMERICAN NATIONAL STANDARD Machine Mounting Specifications for A,brasive Discs and Plate Mounted Wheels ANSI/ASME B5.35-1983 Revision of 85.35-1969(R1975)1.REAFFIRMED 1994 FOR CURRENT COMMllTEE PERSONNEL PLEASE SEE ASME MANUAL AS-1 1 SPONSORED AND PUBLISHED B Y T H E A M E R I C A N S O C I E T Y

2、 O F M E C H A N I C A L E N G I N E E R S United Engineering Center 345 East 47th Street New York,N.Y.10017 REAFFIRMED 2018Date of Issuance:May 31,1984 This Standard will be revised when the Society approves the issuance of a new edition.There will be no addenda or written interpretations of the re

3、quirements of this Standard issued to this Edition.This Code or Standard was developed under procedures accredited as meeting the criteria for American National Standards.The Consensus Committee that approved the code or standard was balanced to assure that individuals from competent and concerned i

4、nterests have had an opportunity to participate.The proposed code or standard was made available for public review and comment which provides an opportunity for additional public input from industry,academia,regulatory agencies,and the public-at-large.ASME does not approve,rate,or endorse any item,c

5、onstruction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted in con-nection with any items mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability for infringement of any applic

6、able Letters Patent,nor asserne any such liability.Users of a code or standard are expressly advised that determination of the validity of any such patent rights,and the risk of infringement of such rights,is entirely their own responsibility.Participation by federal agency representativekd or perso

7、nk)affiliated with industry is not to be interpreted as government or industry eodorsement of this code or standard.ASME does not accept any responsibility for interpretations of this ddcument made by individual volunteers.No part of this document may be reproduced in any form,in an electronic retri

8、eval system or otherwise,without the prior written permission of the publisher.Copyright 01984 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in U.S.A.ERRATA to ANSI/ASME 65.35-1983 MACHINE MOUNTING SPECIFICATIONS FOR ABRASIVE DISCS AND PLATE MOUNTED WHEELS Page 2,Fig.1.

9、2-Correct socket head cap screw to show flat bottom,as illustrated below.3/8 in.-16 X L in socket head cap Steel disc whe!el counreroore-1 I Minimum thick per Table 1.-mess(Machine face plate)Ll W drill(0.3i6)FIG.1.2 DETAIL OF MOUNTING HOLE AND SCREW FOR INSERTED NUT TYPE MOUNTING OCTOBER 1985 THE A

10、MERICAN SOCIETY OF MECHANlCAL ENGINEERS 345 East 47th Street,New York,N.Y.10017 MOOSE FOREWORD(This Foreword is not part of ANSVASME 85.351983.Machine Mounting Specifications for Abrasive Discs and Plate Mounted Wheels.)This Standard,Machine Mounting Specifications for Abrasive Discs and Plate Mount

11、ed Wheels,was approved as an American Standard by the American Standards Association (now the American National Standards Institute)on September 17,1957.The characteristic which makes this class of wheels different from the conventional grinding wheel is the method by which they are mounted on the g

12、rinding machine where grinding is done on the exposed flat side of the wheel.The principal difference is that the power is impacted to the grinding wheel through either inserted nuts,inserted washers,projecting studs anchored on one side of the abrasive wheel,or a mounting plate of steel or other ri

13、gid material cemented to one side of the wheel.The steel wheels (machine face plates)on which these abrasive discs and plate mounted wheels are,mounted must be drilled with holes to match the location and pattern of the holes of the mounting plates or other anchoring devices i n the mounting side of

14、 the abrasive wheels.This Standard was considered for reaffirmation in November 1963 by TC3 1.Certain revisions for clarification were recommended,and the text of the Standard was reorganized and indexed to conform to the B5 style manual.Following approval by TC31 and the B5 Standards Committee,the

15、proposed revision was approved by the sponsors.It was approved by the USA Standards Institute and redesignated a USA Standard on January 3,1969.The present revision was approved by the American National Standards Institute on Octo-ber 17,1983.iii ASME STANDARDS COMMITTEE B5 Machine Tools,Components,

16、Elements,Performance,and Equipment(The following is the roster of the Committee at the time of approval of this Standard.)OFFICERS P.Ackerrnann,Chairman C.Brien,Vice-Chairman,Group 6 H.Cooper,Vice-chairman,Group C W.R.Daisak,Secretary STANDARDS COMMITTEE AMERICAN SOCIETY OF MECHANICAL ENGINEERS,THE R.W.Black,Brown&Sharpe Manufacturing Co.,North Kingstown,Rhode Island F.S.Blackall,Ill,The Taft-Pierce Manufacturing Co.,Woonsocket,Rhode Island DEFENSE INDUSTRIAL PLANT EQUIPMENT CENTER J.W.Lynch,Def

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2