收藏 分享(赏)

ASME_BTH-1-2005.pdf

上传人:益****师 文档编号:167898 上传时间:2023-03-03 格式:PDF 页数:62 大小:11.37MB
下载 相关 举报
ASME_BTH-1-2005.pdf_第1页
第1页 / 共62页
ASME_BTH-1-2005.pdf_第2页
第2页 / 共62页
ASME_BTH-1-2005.pdf_第3页
第3页 / 共62页
ASME_BTH-1-2005.pdf_第4页
第4页 / 共62页
ASME_BTH-1-2005.pdf_第5页
第5页 / 共62页
ASME_BTH-1-2005.pdf_第6页
第6页 / 共62页
亲,该文档总共62页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、ASME BTH-1-2005Design ofBelow-the-HookLifting DevicesAN AMERICAN NATIONAL STANDARDSThe American Society ofMechanical EngineersNot for ResaleASME BTH-1-2005Design ofBelow-the-HookLifting DevicesAN AMERICAN NATIONAL STANDARD拉。The American Society ofMechanical EngineersThree Park Avenue.New York,NY 100

2、16。whAgNo roproduction or natworking permitled without liconso from IHSNot for ResaloCONTENTSForewordCommittee Roster.yCorrespondence With the BTH Committeet月tge,。t。t。t,书年。t。,。t。t。书月。年e年。t。t。t。eg。年。,。+viiChapter 1Scope and Definitions.11-1Purpose11-2Sc0p11-3New and Existing Devices11-4General Requir

3、ements.11-5Definitions31-6Symbols.51-7References8Chapter 2Lifter Classifications.112-1General112-2Design Category112-3Service Class12Chapter 3Structural Design.133-1General.133-2Member Design153-3Connection Design3-4Fatigue Design283-5Other Design Considerations29Chapter 4Mechanical Design404-1Gener

4、al.404-2Sheaves404-3Wire Rope414-4Drive Systems424-5Gearing434-6Bearings4-7Shafting44-8Fasteners47Chapter 5Electrical Components485-1General485-2Electric Motors and Brakes.45-3Limit Switches,Sensors,and Push Buttons5-4Controllers and Rectifiers for Lifting Device Motors.495-5Grounding5-6Power Discon

5、nects55-7Batteries.51FiguresC3-1Selected Examples of Table 3-1 Requirements.C3-2Block Shear2C3-3Pin-Connected Plate Notation.C3-4Stiffened Plate Lifting Beam.24-1Sheave Dimensions4-2Sheave Gap¥进No roproduction or notworking permitled without liconso from IHSNot for ResaleTables2-1Service Class,4C2-1

6、Service Class Life.C3-1Design Category A Static Load Spectrum.14C3-2Design Category A Dynamic Load Spectrum.C3-3Design Category B Static Load Spectrum.14C3-4Design Category B Dynamic Load Spectrum.143-1Limiting Width-Thickness Ratios for Compression Elements.163-2Minimum Effective Throat Thickness o

7、f Partial-Penetration Groove Welds.3-3Minimum Sizes of Fillet Welds.273-4Allowable Stress Ranges,ksi(MPa).23-5Fatigue Design Parameters.304-1Strength Factors for Calculating Load Capacity(American Standard ToothF0rms)434-2Lgg Life.4-3aKey Size Versus Shaft Diameter(ASME B17.1).4-3bKey Size Versus Shaft Diameter(DIN 6885-1).454-4Fatigue Stress Amplification Factors.4No roproduction or notworking permitled without liconso from IHSNot for Resalo

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2