1、AN AMERICAN NATIO NAL STANDAR DDecimal Inch Drawing Sheet Size and FormatASME Y14.1-2005(Revision of ASME Y14.1-1995)Engineering Drawing and Related Documentation PracticesCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University Us
2、er.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME Y14.1ADOPTION NOTICEASME Y14.1,Decimal Inch Drawing Sheet Size and Format,was adopted on 10 March 1995 for use by theDepartment of Defense,DoD.Proposed changes by DoD activities must be submitted to the DoD Adopti
3、ngActivity:Commander,U.S.ARDEC,ATTN:AMSRD-AAR-AIS-SS,Picatinny Arsenal,NJ 07806-5000 or emailedto ardec-stdznpica.army.mil.Copiesof this document maybe purchased from the AmericanSociety of MechanicalEngineers(ASME),22 Law Drive,PO Box 2900,Fairfield,NJ 07007-2900;http:/www.asme.org.Custodians:Adopt
4、ing Activity:Army ARArmy ARNavy SAAir Force 16DLA DHReview Activities:Army CR,IE,PT,TM2Navy AS,CG,CH,EC,NP,TD,YDAir Force 13Other NS,MP,CM,DC2NOTE:The activities listed above were interested in this document as of the date of this document.Sinceorganizations and responsibilities can change,you shoul
5、d verify the currency of the information above usingthe ASSIST Online database at http:/assist.daps.dla.mil.AMSC N/AAREA DRPRDISTRIBUTION STATEMENT A.Approved for public release;distribution is unlimited.Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-0
6、5-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME Y14.1-2005(Revision of ASME Y14.1-1995)Decimal InchDrawing SheetSize and FormatEngineering Drawing and Related Documentation PracticesAN AMERICAN NATIONAL STANDARDThree Park Avenue
7、New York,NY 10016Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Date of Issuance:May 15,2006This Standard will be revised when the Societ
8、y approves the issuance of a new edition.There willbe no addenda or written interpretations of the requirements of this Standard issued to this edition.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as
9、meeting the criteria for American NationalStandards.The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate.The proposed code or standard was madeavailableforpublicreviewandcomment
10、thatprovidesanopportunityforadditionalpublicinputfromindustry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted
11、in connection with anyitems mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent,nor assumes any such liability.Users of a code or standard are expresslyadvised that determination of the validity of
12、 any such patent rights,and the risk of infringement of such rights,isentirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibi
13、lity for only those interpretations of this document issued in accordance with the establishedASME procedures and policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the
14、prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2006 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.Copyrighted material licensed to Stanford University by Thomson Scientific(),
15、downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.CONTENTSForeword.vCommittee Roster.viCorrespondence With the Y14 Committee.vii1General1.1 Scope.11.2 Purpose.11.3 Units.11.4 Applicable Documents.11.5 Definitions.12Dr
16、awing Sheet Sizes.22.1 Margins.22.2 Drawing Sizes.22.3 Computer-Generated Drawings.33Formats.33.1 Basic.33.2 Continuation Sheets.33.3 Blocks.33.4 Lettering.33.5 Zoning.33.6 Lines.43.7 Microfilm Alignment.44Title Blocks.44.1 Location.44.2 Contents.44.3 Continuation Sheet Title Block.45Revision History Block.45.1 Location.45.2 Contents.56Revision Status of Sheets Block.57Associated Lists.58Additional Data Blocks.58.1 Angle of Projection Block.58.2 Dimensioning and Tolerancing Block.58.3 Applicatio