1、MULTIVIEW ANDSECTIONAL VIEWDRAWINGSASME Y14.3-2003Revision of ASME Y14.3M-1994(R1999)MULTIVIEW ANDSECTIONAL VIEWDRAWINGSAn American National StandardEngineering Drawing and RelatedDocumentation PracticesEngineering Drawing and RelatedDocumentation PracticesAn American National StandardASME Y14.3-200
2、3Revision of ASME Y14.3M-1994(R1999)Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME Y14.3ADOPTION NOTICEASME Y14.3,Multiview and Sect
3、ional View Drawings,was adopted on 9 August 1994 for use by the Departmentof Defense,DoD.Proposed changes by DoD activities must be submitted to the DoD Adopting Activity:Com-mander,U.S.Army RDECOM-ARDEC,ATTN:AMSTA-AR-QAW-E,Picatinny Arsenal,NJ 07806-5000.Copies ofthis document may be purchased from
4、 The American Society of Mechanical Engineers(ASME),22 Law Drive,PO Box 2900,Fairfield,NJ 07007-2900;http:/www.asme.org.Custodians:Adopting Activity:Army ARArmy ARNavy SAAir Force 16(Project DRPR-0327)DLA DHReview Activities:Army AT,CR,MINavy AS,CH,EC,MC,TDAir Force 13,99NSA NSAMSC N/AAREA DRPRDISTR
5、IBUTION STATEMENT A.Approved for public release;distribution is unlimited.Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ANAMERICANNATION
6、ALSTANDARDMULTIVIEWANDSECTIONALVIEWDRAWINGSASMEY14.3-2003RevisionofASMEY14.3M-1994(R1999)Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.D
7、ate of Issuance:April 1,2004The next edition of this Standard is scheduled for publication in 2008.There will be no addenda orwritten interpretations of the requirements of this Standard issued to this edition.ASME is the registered trademark of The American Society of Mechanical Engineers.This code
8、 or standard was developed under procedures accredited as meeting the criteria for American NationalStandards.The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate.The proposed c
9、ode or standard was madeavailable forpublic review andcomment thatprovides an opportunityfor additional publicinput from industry,academia,regulatory agencies,and the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any
10、position with respect to the validity of any patent rights asserted in connection with anyitems mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent,nor assumes any such liability.Users of a code or
11、 standard are expresslyadvised that determination of the validity of any such patent rights,and the risk of infringement of such rights,isentirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted asgovernment or i
12、ndustry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued in accordance with the establishedASME procedures and policies,which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in
13、any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,New York,NY 10016-5990Copyright 2004 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.Copyright
14、ed material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.CONTENTSForeword.vCommittee Roster.vi1General.12Multiview Drawing Applied.73Sectional Views.124Conv
15、entional Representation.23Figures1Orthographic Projection to Form an Orthographic View.22Space and Orthographic Arrangement of Views(Third Angle Projection).33Space and Orthographic Arrangement of Views(First Angle Projection).44Third Angle Projection Standard Arrangement of the Six Principal Orthog
16、raphicViews.55First Angle Projection Standard Arrangement of the Six Principal OrthographicViews.56Arrow Method Principal Views.67Arrow Proportions.68Projection Symbol.79Removed View.810Arrow Method Removed View.811Rotated View.912Arrow Method Rotated View.913Rotation Arrow.914Removed View on Multiple Sheet Drawing.1015One View Drawings.1116Two View Drawing.1117Three View Drawing of a Casting.1118Three View Drawing of a Stamping.1219Front View and Partial Auxiliary Views.1220Partial Auxiliary Vi
