1、Designation:D97515cStandard Specification forDiesel Fuel Oils1This standard is issued under the fixed designation D975;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the ye
2、ar of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification covers seven grades of diesel fuel oilssuitable for various types of die
3、sel engines.These grades aredescribed as follows:1.1.1 Grade No.1-D S15A special-purpose,light middledistillate fuel for use in diesel engine applications requiring afuel with 15 ppm sulfur(maximum)and higher volatility thanthat provided by Grade No.2-D S15 fuel.21.1.2 Grade No.1-D S500A special-pur
4、pose,light middledistillate fuel for use in diesel engine applications requiring afuel with 500 ppm sulfur(maximum)and higher volatility thanthat provided by Grade No.2-D S500 fuel.21.1.3 Grade No.1-D S5000A special-purpose,lightmiddle distillate fuel for use in diesel engine applicationsrequiring a
5、 fuel with 5000 ppm sulfur(maximum)and highervolatility than that provided by Grade No.2-D S5000 fuels.1.1.4 Grade No.2-D S15A general purpose,middle dis-tillate fuel for use in diesel engine applications requiring a fuelwith 15 ppm sulfur(maximum).It is especially suitable for usein applications wi
6、th conditions of varying speed and load.21.1.5 Grade No.2-D S500A general-purpose,middledistillate fuel for use in diesel engine applications requiring afuel with 500 ppm sulfur(maximum).It is especially suitablefor use in applications with conditions of varying speed andload.21.1.6 Grade No.2-D S50
7、00A general-purpose,middledistillate fuel for use in diesel engine applications requiring afuel with 5000 ppm sulfur(maximum),especially in conditionsof varying speed and load.1.1.7 Grade No.4-DA heavy distillate fuel,or a blend ofdistillate and residual oil,for use in low-and medium-speeddiesel eng
8、ines in applications involving predominantly con-stant speed and load.NOTE1A more detailed description of the grades of diesel fuel oils isgiven in X1.2.NOTE2The Sxxx designation has been adopted to distinguish gradesby sulfur rather than using words such as“Low Sulfur”as previouslybecause the numbe
9、r of sulfur grades is growing and the word descriptionswere thought to be not precise.S5000 grades correspond to the so-called“regular”sulfur grades,the previous No.1-D and No.2-D.S500 gradescorrespond to the previous“Low Sulfur”grades.S15 grades were not inthe previous grade system and are commonly
10、 referred to as“Ultra-LowSulfur”grades or ULSD.1.2 This specification,unless otherwise provided by agree-ment between the purchaser and the supplier,prescribes therequired properties of diesel fuels at the time and place ofdelivery.1.2.1 Nothing in this specification shall preclude observanceof fede
11、ral,state,or local regulations which can be morerestrictive.NOTE3The generation and dissipation of static electricity can createproblems in the handling of distillate diesel fuel oils.For more informa-tion on the subject,see Guide D4865.1.3 The values stated in SI units are to be regarded asstandard
12、.No other units of measurement are included in thisstandard.2.Referenced Documents2.1 ASTM Standards:3D56 Test Method for Flash Point by Tag Closed Cup TesterD86 Test Method for Distillation of Petroleum Products atAtmospheric PressureD93 Test Methods for Flash Point by Pensky-MartensClosed Cup Test
13、erD129 Test Method for Sulfur in Petroleum Products(Gen-eral High Pressure Decomposition Device Method)D130 Test Method for Corrosiveness to Copper from Petro-leum Products by Copper Strip Test1This specification is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and L
14、ubricants and is the direct responsibility ofSubcommittee D02.E0 on Burner,Diesel,Non-Aviation Gas Turbine,and MarineFuels.Current edition approved Oct.1,2015.Published November 2015.Originallyapproved in 1948.Last previous edition approved in 2015 as D975 15b.DOI:10.1520/D0975-15C.2This fuel compli
15、es with 40 CFR Part 80Control of Air Pollution from NewMotor Vehicles:HeavyDuty Engines and Vehicle Standards and Highway DieselFuel Sulfur Control Requirements:Final Rule.Regulation of Fuels and FuelAdditives:Fuel Quality Regulations for Highway Diesel Fuel Sold in 1993 andLater Calendar Years.3For
16、 referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 D445 Test Method for Kinematic Viscosity of Transparentand Opaque Liquids(and Calculation of Dy
