1、Designation:E117097(Reapproved 2017)Standard Practices forSimulating Vehicular Response to Longitudinal Profiles ofTraveled Surfaces1This standard is issued under the fixed designation E1170;the number immediately following the designation indicates the year oforiginal adoption or,in the case of rev
2、ision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 These practices cover the calculation of vehicular re-sponse to longitudinal profiles of traveled surface
3、 roughness.1.2 These practices utilize computer simulations to obtaintwo vehicle responses:(1)axle-body(sprung mass)motion or(2)body(sprung mass)acceleration,as a function of time ordistance.1.3 These practices present standard vehicle simulations(quarter,half,and full car)for use in the calculation
4、s.1.4 The values stated in SI units are to be regarded as thestandard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the ap
5、plica-bility of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued b
6、y the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2E950 Test Method for Measuring the Longitudinal Profile ofTraveled Surfaces with an Accelerometer EstablishedInertial Profiling Reference2.2 ISO Standard:3ISO 2631 Guide for the Evaluati
7、on of Human Exposure toWhole-Body Vibration3.Summary of Practices3.1 These practices use a measured profile(see Test MethodE950)or a synthesized profile as part of a vehicle simulation toobtain vehicle response.3.2 The first practice for obtaining vehicle response usessimulation of a quarter-car or
8、half-car model.The output is theaccumulated relative motion between the sprung and unsprungvehicle masses,of the simulated vehicle,for a predetermineddistance.The units are accumulated relative motion per unit ofdistance traveled(m/km or in./mile).For example,the quarter-car simulation is used when
9、a Bureau of Public RoadsBPR/roadmeter is to be simulated,and the half-car model(orthe quarter car with the average of the left and right elevationprofile input)is used when a road meter is to be simulated.3.3 The second practice uses either a quarter-car,half-car,orfull-car simulation to obtain vehi
10、cle body acceleration.Theacceleration history can be computed as a function of time ordistance,or both.One application of this practice is to use theacceleration history in a ride quality evaluation,such as theISO Guide 2631.3.4 For all calculations,a vehicle test speed is selected andmaintained thr
11、oughout the calculation.Pertinent informationaffecting the results must be noted.4.Significance and Use4.1 These practices provide a means for evaluating traveledsurface-roughness characteristics directly from a measuredprofile.The calculated values represent vehicular response totraveled surface ro
12、ughness.4.2 These practices provide a means of calibrating response-type road-roughness measuring equipment.45.Apparatus5.1 ComputerThe computer is used to calculate accelera-tion and displacement of vehicle response to a traveled surfaceprofile,using a synthesized profile or a profile obtained inac
13、cordance with Test Method E950 as the input.Filtering shall1These practices are under the jurisdiction of ASTM Committee E17 on Vehicle-Pavement Systems and are the direct responsibility of Subcommittee E17.33 onMethodology for Analyzing Pavement Roughness.Current edition approved July 1,2017.Publis
14、hed July 2017.Originally approvedin 1987.Last previous edition approved in 2012 as E1170 97(2012).DOI:10.1520/E1170-97R17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to
15、 the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.4Gillespie,T.D.,Sayers,M.W.,and Segel,L.,“Calibration and Correlation ofResponse-Type Road Roughness Measuring Systems,”NCH
16、RP Report 228,1980.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 be provided to permit calculation,without attenuation,atf
