1、Designation:D97621Standard Test Method forCalculated Cetane Index of Distillate Fuels1This standard is issued under the fixed designation D976;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in pare
2、ntheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This test method covers the Calculated Cetane Indexformula,which re
3、presents a means for directly estimating theASTM cetane number of distillate fuels from API gravity andmid-boiling point.The index value,as computed from theformula,is termed the Calculated Cetane Index.21.2 The Calculated Cetane Index is not an optional methodfor expressingASTM cetane number.It is
4、a supplementary toolto estimate cetane number when used with due regard for itslimitations.1.3 The Calculated Cetane Index formula is particularlyapplicable to straight-run fuels,catalytically cracked stocks,and blends of the two.NOTE1This test method is temporarily retained because the proposalto t
5、he U.S.EPA to control diesel fuel aromatics concentrations via a 40Calculated Cetane Index minimum is based on the correlation betweenTest Method D976 and aromatics concentration.Test Method D4737 is thepreferred method as estimator of cetane number.1.4 This standard does not purport to address all
6、of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor
7、-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Sta
8、ndards:3D86 Test Method for Distillation of Petroleum Products andLiquid Fuels at Atmospheric PressureD287 Test Method for API Gravity of Crude Petroleum andPetroleum Products(Hydrometer Method)D613 Test Method for Cetane Number of Diesel Fuel OilD1298 Test Method for Density,Relative Density,or API
9、Gravity of Crude Petroleum and Liquid Petroleum Prod-ucts by Hydrometer MethodD2887 Test Method for Boiling Range Distribution of Pe-troleum Fractions by Gas ChromatographyD4052 Test Method for Density,Relative Density,and APIGravity of Liquids by Digital Density MeterD4175 Terminology Relating to P
10、etroleum Products,LiquidFuels,and LubricantsD4737 Test Method for Calculated Cetane Index by FourVariable Equation2.2 ASTM Adjuncts:4Nomograph for Calculated Cetane Index3.Terminology3.1 For definitions of terms used in this test method,refer toTerminology D4175.4.Significance and Use4.1 The Calcula
11、ted Cetane Index is one tool available forestimating ASTM cetane number where a test engine is notavailable for determining this property.It may be employed forapproximating cetane number where the quantity of sample istoo small for an engine rating.In cases where the cetanenumber of a fuel has been
12、 initially established,the index isuseful as a cetane number check on subsequent samples of thatfuel,provided its source and mode of manufacture remainunchanged.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct respon
13、sibility ofSubcommittee D02.E0 on Burner,Diesel and Non-Aviation Gas Turbine Fuels.Current edition approved Nov.1,2021.Published November 2021.Originallyapproved in 1966.Last previous edition approved in 2016 as D976 06(2016).DOI:10.1520/D0976-21.2A method of calculating cetane index was developed b
14、y the Diesel FuelsDivision,Coordinating Fuel and Equipment Research Committee of the Coordinat-ing Research Council.See Young,H.D.,“Methods for Estimating Cetane Number,”Proceedings,PPIRA,American Petroleum Institute,Vol.30 M III,1950.Thismethod was revised in 1960 by Research Division I of Committe
15、e D02 to conformto the revised Test Method D613.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4Available from AS
16、TM International Headquarters.Order Adjunct No.ADJD0976.Original adjunct produced in 1989.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issu
