1、Designation:E1139/E1139M17Standard Practice forContinuous Monitoring of Acoustic Emission from MetalPressure Boundaries1This standard is issued under the fixed designation E1139/E1139M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,
2、the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This practice provides guidelines for continuous moni-toring of acoustic emission(AE)from metal pressure boun
3、d-aries in industrial systems during operation.Examples arepressure vessels,piping,and other system components whichserve to contain system pressure.Pressure boundaries otherthan metal,such as composites,are specifically not covered bythis document.1.2 The functions of AE monitoring are to detect,lo
4、cate,and characterize AE sources to provide data to evaluate theirsignificance relative to pressure boundary integrity.Thesesources are those activated during system operation,that is,nospecial stimulus is applied to produce AE.Other methods ofnondestructive testing(NDT)may be used,when the pressure
5、boundary is accessible,to further evaluate or substantiate thesignificance of detected AE sources.1.3 UnitsThe values stated in either SI units or inch-pound units are to be regarded as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independe
6、ntly of the other.Combiningvalues from the two systems may result in non-conformancewith the standards.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and heal
7、th practices and determine the applica-bility of regulatory limitations prior to use.For specificprecautionary statements,see Section 6.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principle
8、s for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2E543 Specification for Agencies Performing NondestructiveTestingE569 Practice for Acoustic Emission Mo
9、nitoring of Struc-tures During Controlled StimulationE650 Guide for Mounting Piezoelectric Acoustic EmissionSensorsE750 Practice for Characterizing Acoustic Emission Instru-mentationE976 Guide for Determining the Reproducibility ofAcousticEmission Sensor ResponseE1316 Terminology for Nondestructive
10、ExaminationsE2374 Guide for Acoustic Emission System PerformanceVerification2.2 Aerospace Industries Association:3NAS-410 Certification and Qualification of NondestructiveTesting Personnel2.3 Other Documents:4SNT-TC-1A Recommended Practice for NondestructiveTesting Personnel Qualification and Certif
11、icationANSI/ASNT CP-189 ASNT Standard for Qualification andCertification of Nondestructive Testing Personnel2.4 ISO Standard:5ISO 9712 Non-Destructive Testing:Qualification and Certi-fication of NDT Personnel3.Terminology3.1 Definitions:3.1.1 For definitions of terms used in this practice,refer toTe
12、rminology E1316.1This practice is under the jurisdiction of ASTM Committee E07 on Nonde-structive Testing and is the direct responsibility of Subcommittee E07.04 onAcoustic Emission Method.Current edition approved June 1,2017.Published June 2017.Originallyapproved in 1987.Last previous edition appro
13、ved in 2012 as E1193-12.DOI:10.1520/E1139-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Aeros
14、pace Industries Association of America,Inc.(AIA),1000Wilson Blvd.,Suite 1700,Arlington,VA22209-3928,http:/www.aia-aerospace.org.4Available fromAmerican Society for Nondestructive Testing(ASNT),P.O.Box28518,1711 Arlingate Ln.,Columbus,OH 43228-0518,http:/www.asnt.org.5Available from International Org
15、anization for Standardization(ISO),ISOCentral Secretariat,BIBC II,Chemin de Blandonnet 8,CP 401,1214 Vernier,Geneva,Switzerland,http:/www.iso.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428
16、-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.2 Definitions of Terms Specific to This Standard:3.2.1 continuous monitoringthe process of monitoring apressure boundary continuously to detect acoustic emissiondu
