1、Designation:E218810An American National StandardStandard Test Method forInsulating Glass Unit Performance1This standard is issued under the fixed designation E2188;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revi
2、sion.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers procedures for testing theperformance of preassembled permanently sealed insulatingglass units or insulating
3、 glass units with capillary tubesintentionally left open.1.2 This test method is applicable only to sealed insulatingglass units that are constructed with glass.1.3 This test method is applicable to both double-glazed andtriple-glazed insulating glass units.For triple-glazed insulatingglass units wh
4、ere both of the outer lites are glass and the innerlite is either glass or a suspended film.1.4 The unit construction used in this test method containsdimensions that are an essential component of the test.Differ-ent types of glass,different glass thicknesses,and differentairspace sizes may affect t
5、he test results.1.5 This test method is not applicable to sealed insulatingglass units containing a spandrel glass coating due to testinglimitations.1.6 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.7 This standard does not p
6、urport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2C162
7、 Terminology of Glass and Glass ProductsC717 Terminology of Building Seals and SealantsC1036 Specification for Flat GlassE631 Terminology of Building ConstructionsE546 Test Method for Frost/Dew Point of Sealed InsulatingGlass UnitsE2190 Specification for Insulating Glass Unit Performanceand Evaluati
8、on3.Terminology3.1 Definition of Terms:3.1.1 For definitions of terms found in this standard,refer toTerminologies C162,C717,and E631.3.2 Definitions of Terms Specific to This Standard:3.2.1 frost/dew point,nthe temperature at which water,organic vapor,or other chemicals begin to appear on theinteri
9、or glass surface of a sealed insulating glass unit.4.Significance and Use4.1 This test method is intended to provide a means fortesting the performance of the sealing system and constructionof sealed insulating glass units.4.1.1 Sealed insulating glass units tested in accordance withthis method may
10、be suitable for structurally glazed applica-tions.However,factors such as sealant longevity when ex-posed to long term ultraviolet light and the structural propertiesof the sealant must be reviewed for these applications.4.1.2 Sealed insulating glass units tested in accordance withthis method are no
11、t intended for continuous exposure to highrelative humidity conditions or long-term immersion in water.5.Test Specimens5.1 Each test specimen shall measure 355 6 6 mm by505 6 6 mm and shall be composed of two or three lites ofclear,tinted or coated annealed,heat-strengthened,tempered,or laminated gl
12、ass.5.1.1 The double-glazed test samples shall be fabricatedwith at least one lite of clear,uncoated glass.The triple-glazedtest samples shall be fabricated with at least one outer lite ofclear,uncoated glass.The other outer lite shall be fabricatedwith a glass which allows easy viewing of the frost
13、 point.5.1.2 The thickness of the glass lites shall be betweennominal 3.0 mm and a maximum of 6.0 mm nominal.5.1.3 The airspaces for units with either two or three lites ofglass shall be a minimum of 6.0 6 0.8 mm.5.1.4 When testing to Specification E2190 the specimenconstruction shall be as defined
14、in that document.1This test method is under the jurisdiction of ASTM Committee E06 onPerformance of Buildings and is the direct responsibility of Subcommittee E06.22on Durability Performance of Building Constructions.Current edition approved Nov.1,2010.Published February 2011.Originallyapproved in 2
15、002.Last previous edition approved in 2002 as E2188 02.DOI:10.1520/E2188-10.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe AST
16、M website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 5.1.5 Triple-pane units where the intermediate airspacedivider is a plastic film are acceptable.NOTE1Overall unit thickness has some limits.Testing laboratoriesare usually able to accommodate 30 mm overall thickness.If testingthicker units,contact the testing laboratory prior to manufacturing toascertain their capabilities for testing thicker units.5.2 The thickness tolerance o
