收藏 分享(赏)

ASTM_E_2611_-_09.pdf

上传人:益****师 文档编号:169591 上传时间:2023-03-04 格式:PDF 页数:14 大小:314.26KB
下载 相关 举报
ASTM_E_2611_-_09.pdf_第1页
第1页 / 共14页
ASTM_E_2611_-_09.pdf_第2页
第2页 / 共14页
ASTM_E_2611_-_09.pdf_第3页
第3页 / 共14页
ASTM_E_2611_-_09.pdf_第4页
第4页 / 共14页
ASTM_E_2611_-_09.pdf_第5页
第5页 / 共14页
ASTM_E_2611_-_09.pdf_第6页
第6页 / 共14页
亲,该文档总共14页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:E261109Standard Test Method forMeasurement of Normal Incidence Sound Transmission ofAcoustical Materials Based on the Transfer Matrix Method1This standard is issued under the fixed designation E2611;the number immediately following the designation indicates the year oforiginal adoption o

2、r,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the use of a tube,fourmicrophones,and a digital frequency ana

3、lysis system for themeasurement of normal incident transmission loss and otherimportant acoustic properties of materials by determination ofthe acoustic transfer matrix.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This

4、 standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1

5、ASTM Standards:2C634 Terminology Relating to Building and EnvironmentalAcousticsE90 Test Method for Laboratory Measurement of AirborneSound Transmission Loss of Building Partitions andElementsE1050 Test Method for Impedance and Absorption ofAcoustical Materials Using a Tube,Two Microphones anda Digi

6、tal Frequency Analysis System2.2 ISO Standards:ISO 140-3 AcousticsMeasurement of Sound Insulation inBuildings and of Building ElementsPart 3:LaboratoryMeasurement of Airborne Sound Insulation of BuildingElements33.Terminology3.1 DefinitionsThe acoustical terminology used in this testmethod is intend

7、ed to be consistent with the definitions inTerminology C634.3.1.1 reference planean arbitrary section,perpendicular tothe longitudinal axis of the tube that is used for the origin oflinear dimensions.Often it is the upstream(closest to the soundsource)face of the specimen but,when specimen surfaces

8、areirregular,it may be any convenient plane near the specimen.3.1.2 sound transmission coeffcient,(dimensionless)ofa material in a specified frequency band,the fraction ofairborne sound power incident on a material that is transmittedby the material and radiated on the other side.5WtWiwhere:Wtand Wi

9、=the transmitted and incident sound power.3.1.3 sound transmission loss,TLof a material in a speci-fied frequency band,ten times the common logarithm of thereciprocal of the sound transmission coefficient.The quantityso obtained is expressed in decibels.TL5 10 log10SWiWtD5 10 log10S1D3.1.3.1 Discuss

10、ionIn this standard the symbol TLnwill beapplied to sound which impinges at an angle normal to the testspecimen,as opposed to an arbitrary or random angle ofincidence.3.2 Symbols:c=speed of sound,m/s.=density of air,kg/m3.f=frequency,hertz,(Hz).G11,G22,etc.=auto power spectra(autospectrum)of theacou

11、stic pressure signal at microphone locations 1,2,and soon.G21,G32,etc.=cross power spectrum(cross spectrum)ofthe acoustic pressure signals at location 2 relative to location 1,3 relative to 1,and so on.In general,a complex value.H21,H31,etc.=measured transfer function of the acousticpressure signals

12、 at location 2 relative to location 1,3 relative to1This test method is under the jurisdiction ofASTM Committee E33 on Buildingand Environmental Acoustics and is the direct responsibility of SubcommitteeE33.03 on Sound Transmission.Current edition approved March 1,2009.Published March 2009.DOI:10.15

13、20/E2611-09.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(

14、ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 1,and so on.In general,a complex value.Note that H11ispurely real and equal to 1.HI,HII=calibration transfer functions for

15、the microphonesin the standard and switched configurations,respectively.See8.4.Hc=complex microphone calibration factor accounting formicrophone response mismatch.H21,H31,etc.=transfer function of two microphone signalscorrected for microphone response mismatch.In general,acomplex value.NOTE1In this

16、 context,the term“transfer function”refers to thecomplex ratio of the Fourier transform of two signals.The term“fre-quency response function”arises from more general linear system theory(1).4This test method shall retain the use of the former term.Users shouldbe aware that modern FFT analyzers might employ the latter terminology.j=21k=2f/c;wave number in air,m-1.NOTE2In general the wave number is complex where k=kr jki.kris the real component,2 f/c,and kiis the imaginary component of thewave num

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2