1、Designation:E244305(Reapproved 2010)1Standard Guide forVerifying Computer-Generated Test Results Through TheUse Of Standard Data Sets1This standard is issued under the fixed designation E2443;the number immediately following the designation indicates the year oforiginal adoption or,in the case of re
2、vision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTE3.1.2 and 3.1.4 were editorially updated in December 2011.1.Scope1.1 This guide establishes a process for the
3、verification ofapplication software used to calculate the mechanical proper-ties of materials.1.2 This guide has two purposes:(1)it provides guidelinesfor creating standard data sets for verifying computer-generated test results,and(2)it describes how users can verifywhether the calculations in thei
4、r application software produceaccurate,acceptable results.This does not ensure that thesoftware will produce correct results in all cases.The verifi-cation is only for those conditions covered by the standard datasets.This guide uses the concept of standard“data sets,”whichare made available by the
5、ASTM groups responsible for eachof the individual standards.1.3 This guide defines the terminology,the format,and theprocess for the use of these data sets and how the data sets areto be used for verification.It does not define the specific datasets required to verify each of the application standar
6、ds.Rather,such data sets would become a necessary part of thestandard and would be classified as an adjunct in accord withthe definition in section B29 of the“Form and Style for ASTMStandards.”This classifies an adjunct as any material that isrequired for use of the standard but is not practicable t
7、o publishas an integral part of the standard.1.4 In Annex A1 there is an example of how such data setswould be made available for one example standard.1.5 Because the verification data sets are contained in filessupplied to the application software in the computer,thisprocedure only provides verific
8、ation of post-test calculationsperformed by the computer system.It does not evaluate thedata acquisition system,real-time calculations,or any otherpart of the software beyond the post-test calculations.2.Referenced Documents2.1 ASTM Standards:2E1823 Terminology Relating to Fatigue and Fracture Testi
9、ngE1942 Guide for Evaluating Data Acquisition Systems Usedin Cyclic Fatigue and Fracture Mechanics TestingE1856 Guide for Evaluating Computerized Data AcquisitionSystems Used to Acquire Data from Universal TestingMachines3.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 ASCIIAmer
10、ican National Standard Code for Infor-mation Interchange.Data supplied in this form is readable byany computer system and will be displayed on the screen inhuman readable form.3.1.2 raw datathe sampled values of a sensor output.3.1.3 data setA self-contained set of data consisting of apreamble,speci
11、men information,and basic data.This may takethe form of a printed document or a computer data file.3.1.4 derived datadata obtained through the processing ofthe raw data.3.1.5 expected resultsThe results accompanying the datasets that are expected from the computer.3.1.6 item separatorA special chara
12、cter(delimiter)usedto separate items that appear on one line of ASCII characters.3.1.7 keywordA text word or combination of charactersthat uniquely identify an item of information in the SpecimenInformation section.Such keywords are defined in a preambleto the data set within the standard in which t
13、hey are to be used.3.1.8 line terminatorAcharacter or sequence of charactersused to signify the end of a line of ASCII characters.3.1.9 preambleA text section describing the data set,which standard it applies to,any critical information andrestrictions for use of the data sets,and the expected value
14、s1This guide is under the jurisdiction of ASTM Committee E08 on Fatigue andFracture and is the direct responsibility of Subcommittee E08.03 on AdvancedApparatus and Techniques.Current edition approved Nov.1,2010.Published January 2011.Originallyapproved in 2005.Last previous edition approved in 2005
15、 as E2443-05.DOI:10.1520/E2443-05R10E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM Internation
16、al,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1(derived data)to be found as a result of running the algorithmusing the basic data.This section of the data set would not beused by the computer,and would normally be stripped off ofthe data set prior to its use with the computer.3.1.10 segment markerA column of data alongside thecolumns of basic data which indicate different control sectionsduring the test,such as loading versus unloading sections,which might be
