收藏 分享(赏)

ASTM_D_7952_-_15_2021.pdf

上传人:益****师 文档编号:170085 上传时间:2023-03-04 格式:PDF 页数:3 大小:81.98KB
下载 相关 举报
ASTM_D_7952_-_15_2021.pdf_第1页
第1页 / 共3页
ASTM_D_7952_-_15_2021.pdf_第2页
第2页 / 共3页
ASTM_D_7952_-_15_2021.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D795215(Reapproved 2021)Standard Test Method forMeasuring Aspiration Potential of Aerosol Products1This standard is issued under the fixed designation D7952;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last

2、 revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers a small-scale laboratory proce-dure to determine the aspiration potential of aerosol productsby determi

3、ning spray pattern and aerosol deposition rates.1.2 This test method has been developed to address a needto identify which aerosol products may present an aspirationrisk such that special labeling and/or child-resistant packagingwould be appropriate.Studies based on this method may allowthe developm

4、ent of a practice to identify such aerosol products.1.3 Although this method may be useful for testing non-pressurized aerosol products,its development has been limitedto testing pressurized aerosols.1.4 The values stated in inch-pound units are to be regardedas standard.The values given in parenthe

5、ses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safe

6、ty,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of In

7、ternational Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Terminology2.1 Definitions:2.1.1 aerosol product,na product that dispenses liquid asan aerosol.2.1.2 ballistic stream(or stream),na stream pattern thatdeposits entirely

8、 in the test cup.2.1.3 cone spray,nspray pattern where the bottom of thetest cup is completely covered during a 5 to 7 s test but aportion of the aerosol is deposited outside of the cup during theentire test.2.1.4 deposition rate,nthe amount of aerosol(in grams)that dispenses in a test cup in one se

9、cond.2.1.5 mist,nspray pattern where the aerosol only partiallycovers the bottom of the test cup during a 5 to 7 s test.2.1.6 pressurized aerosol product,nan aerosol productthat is self-pressurized and does not require pumping todispense an aerosol.2.1.7 spray pattern,nthe pattern in which an aeroso

10、l isdispensed and deposited.3.Summary of Test Method3.1 After shaking and discarding 5 s worth of spray,the testaerosol is sprayed onto a test cup held in place with sticky waxfrom an aligning apparatus(see Fig.1)for 5 to 7 s.The test cupis weighed before the test and within 60 s after concluding th

11、etest.4.Significance and Use4.1 This test method provides a means of measuringwhether or not an aerosol product may present an aspirationrisk if a dispensed aerosol gets into ones mouth.4.2 The degree of risk for aspiration of an aerosol dependsboth on spray pattern as well as aerosol deposition rat

12、e.24.3 This test method will be used to determine the need forchild-resistant packaging of aerosol products.5.Apparatus5.1 Scale,sensitive to 0.0001 g.5.2 6.0 cm Aluminum Weighing Cups.5.3 Jewelers Sticky Wax.5.4 Stopwatch,sensitive to1100th s.5.5 Plexiglas Sheet,2 by 3 ft.1This test method is under

13、 the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.57 on Artist Paints and Related Materials.Current edition approved Nov.1,2021.Published November 2021.Originallyapproved in 2015.Last previous edition a

14、pproved in 2015 as D7952 15.DOI:10.1520/D7952-15R21.2Supporting data have been filed at ASTM International Headquarters and maybe obtained by requesting Research Report RR:D01-1179.ContactASTM CustomerService at serviceastm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Cons

15、hohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organ

16、ization Technical Barriers to Trade(TBT)Committee.1?5.6 Aligning Apparatus,see Fig.1.6.Procedure6.1 Weigh weighing cup to nearest 0.0001 g and attach tomiddle of Plexiglas sheet with jewelers sticky wax.6.2 Set aligning apparatus at end of Plexiglas sheet so thatvertical is exactly 11 in.(28 cm)from the center of the test cup.6.3 Shake aerosol container according to directions or for 1min.if directions are not available.6.4 Spray aiming to hit the middle of the test cup.Continuespraying for 5 to

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2