收藏 分享(赏)

ASTM_E_2336_-_14.pdf

上传人:益****师 文档编号:170163 上传时间:2023-03-04 格式:PDF 页数:15 大小:672.17KB
下载 相关 举报
ASTM_E_2336_-_14.pdf_第1页
第1页 / 共15页
ASTM_E_2336_-_14.pdf_第2页
第2页 / 共15页
ASTM_E_2336_-_14.pdf_第3页
第3页 / 共15页
ASTM_E_2336_-_14.pdf_第4页
第4页 / 共15页
ASTM_E_2336_-_14.pdf_第5页
第5页 / 共15页
ASTM_E_2336_-_14.pdf_第6页
第6页 / 共15页
亲,该文档总共15页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:E233614An American National StandardStandard Test Methods forFire Resistive Grease Duct Enclosure Systems1This standard is issued under the fixed designation E2336;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year

2、of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.INTRODUCTIONThe protection of grease ducts under fire exposure conditions is an item of importance in securingconstructions that ar

3、e safe,and that are not a menace to neighboring construction nor to the public.Recognition of this is registered in the codes of many authorities,municipal and other agencies.Manytypes of enclosure materials are used to protect grease ducts.Normally,these enclosure materials areeither applied to gre

4、ase ducts in the field or are fabricated as part of the grease duct when shipped fromthe factory.Evaluating enclosure materials used to protect a grease duct from fire is an aid forpredicting their fire performance and promotes uniformity in requirements of various authorities.Todo this it is necess

5、ary that the fire-endurance properties of enclosure materials be measured andspecified according to a common standard expressed in terms that are applicable alike to a wide varietyof materials,situations,and conditions of exposure.1.ScopeNOTE1The majority of this standard is based on the Model Build

6、ingCode Evaluation Service2Acceptance Criteria titled ACCEPTANCECRITERIA FOR GREASE DUCT ENCLOSURE ASSEMBLIES,AC101,which was created in 1994.Numerous design listings and labeledmaterials exist based on the provisions of this standard.1.1 These test methods evaluate the enclosure materials andthe gr

7、ease duct enclosure systems using the following testmethods:noncombustibility,fire resistance,durability,internalfire,and fire-engulfment with a through-penetration fire stop.1.2 These test methods prescribe a standardized fire expo-sure for comparing the test results of the enclosure materialsand g

8、rease duct enclosure systems.The results of these tests areone factor in assessing predicted fire performance of greaseduct enclosure systems.Using these test results to predict theperformance of actual grease duct enclosure systems requiresthe evaluation of test conditions.1.3 The values stated in

9、inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 The text of these test methods references notes andfootnotes which provide explanatory material.These notes

10、 andfootnotes(excluding those in tables and figures)shall not beconsidered as requirements of the fire test response standard.1.5 These test methods are used to measure and describe theresponse of materials,products,or assemblies to heat andflame under controlled conditions,but does not by itselfinc

11、orporate all factors required for fire hazard or fire riskassessment of the materials,products,or assemblies underactual fire conditions.1.6 These test methods do not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of these test methods

12、 to establishappropriate safety and health practices and to determine theapplicability of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:3C518 Test Method for Steady-State Thermal TransmissionProperties by Means of the Heat Flow Meter ApparatusC569 Test Method for Inden

13、tation Hardness of PreformedThermal Insulations(Withdrawn 1988)4E84 Test Method for Surface Burning Characteristics ofBuilding MaterialsE119 Test Methods for Fire Tests of Building Constructionand Materials1This test method is under the jurisdiction of ASTM Committee E05 on FireStandards and is the

14、direct responsibility of Subcommittee E05.11 on FireResistance.Current edition approved Aug.1,2014.Published September 2014.Originallyapproved in 2004.Last previous edition approved in 2013 as E233604(2013).DOI:10.1520/E2336-14.2ICC Evaluation Service,Inc.(ICBO Evaluation Service,Inc.)5360 WorkmanMi

15、ll Road,Whittier,CA 90601-22983For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4The last approved version of this h

16、istorical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 E136 Test Method for Behavior of Materials in a VerticalTube Furnace at 750CE176 Terminology of Fire StandardsE631 Terminology of Building ConstructionsE814 Test Method for Fire Tests of Penetration FirestopSystems2.2 Other Documents:UL 385 Standard for Play Pipes for Water Supply Testing inFire-Protection Service53.Terminology3.1 Definitio

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2