1、Designation:D710113Standard Index Test Method forDetermination of Unvegetated Rolled Erosion ControlProduct(RECP)Ability to Protect Soil from Rain Splash andAssociated Runoff Under Bench-Scale Conditions1This standard is issued under the fixed designation D7101;the number immediately following the d
2、esignation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This index test method establishe
3、s the guidelines,re-quirements and procedures for evaluating the ability of unveg-etated rolled erosion control products(RECPs)to protect soilsfrom simulated rainfall(rain splash)and minimal runoffinduced erosion.The critical element of this protection is theability of the unvegetated RECP to absorb
4、 the impact force ofraindrops,thereby reducing soil particle loosening through“splash”mechanisms,and limiting the ability of runoff to carrythe loosened soil particles.1.2 This index test method utilizes bench-scale testingprocedures and is not indicative of unvegetated RECP perfor-mance in conditio
5、ns typically found in the field.NOTE1The values obtained with this bench scale procedure are forinitial performance indication,general product comparison and confor-mance purposes only.These values should not be used in estimating RECPsoil protection in actual field use with such calculations as the
6、 UniversalSoil Loss Equation(USLE)or Revised Universal Soil Loss Equation(RUSLE)without verification from qualified,large-scale tests.1.3 This index test is not intended to replace full-scalesimulation or field testing in acquisition of performance valuesthat are required in the design of erosion co
7、ntrol measuresutilizing unvegetated RECPs.1.4 The values stated in SI units are to be regarded asstandard.The values given in parentheses are mathematicalconversions to inch-pound units that are provided for informa-tion only and are not considered standard.1.5 All observed and calculated values sha
8、ll conform to theguidelines for significant digits and rounding established inPractice D6026,unless superseded by this standard.1.5.1 The procedures used to specify how data are collected/recorded or calculated in this standard are regarded as theindustry standard.In addition,they are representative
9、 of thesignificant digits that generally should be retained.The proce-dures used do not consider material variation,purpose forobtaining the data,special purpose studies,or any consider-ations for the users objectives,and it is common practice toincrease or reduce significant digits of reported data
10、 to becommensurate with these considerations.It is beyond the scopeof this index test method to consider significant digits used inanalytical methods for engineering design.1.6 This standard does not purport to address all of thesafety concerns,if any,associated with its use and may involveuse of ha
11、zardous materials,equipment,and operations.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.Also,the user mustcomply with prevalent regulatory codes,such as OSHA(Oc-cupat
12、ional Health and Safety Administration)guidelines,whileusing the index test method.2.Referenced Documents2.1 ASTM Standards:2D653 Terminology Relating to Soil,Rock,and ContainedFluidsD698 Test Methods for Laboratory Compaction Character-istics of Soil Using Standard Effort(12 400 ft-lbf/ft3(600kN-m/
13、m3)D6026 Practice for Using Significant Digits in GeotechnicalDataD3740 Practice for Minimum Requirements for AgenciesEngaged in Testing and/or Inspection of Soil and Rock asUsed in Engineering Design and ConstructionD6459 Test Method for Determination of Rolled ErosionControl Product(RECP)Performan
14、ce in Protecting Hill-slopes from Rainfall-Induced ErosionD6475 Test Method for Measuring Mass Per Unit Area ofErosion Control BlanketsD6566 Test Method for Measuring Mass per Unit Area ofTurf Reinforcement Mats1This test method is under the jurisdiction ofASTM Committee D18 on Soil andRock and is t
15、he direct responsibility of Subcommittee D18.25 on Erosion andSediment Control Technology.Current edition approved June 15,2013.Published July 2013.Originallyapproved in 2007.Last previous edition approved in 2008 as D7101 08.DOI:10.1520/D7101-13.2For referenced ASTM standards,visit the ASTM website
16、,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.Terminology3.1 DefinitionsFor common definitions of terms in thisstandard,refer to Terminology D653.4.Summary of Test Method4.1 Soil cores con
