1、Designation:D703004(Reapproved 2022)Standard Test Method forShort Term Creep Performance of Corrugated FiberboardContainers Under Constant Load Using a Compression TestMachine1This standard is issued under the fixed designation D7030;the number immediately following the designation indicates the yea
2、r oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers determining the resistance of anempty
3、paper corrugated shipping container to a verticallyapplied constant compression load for a specified time.The testmethod may also include palletized or unitized loads made ofsuch containers.The boxes are tested in the orientation thatthey are most likely to be stacked in a unitized or palletizedload
4、.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associ
5、ated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles
6、 on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D642 Test Method for Determining Compress
7、ive Resistanceof Shipping Containers,Components,and Unit LoadsD644 Test Method for Moisture Content of Paper andPaperboard by Oven Drying(Withdrawn 2010)3D685 Practice for Conditioning Paper and Paper Productsfor TestingD996 Terminology of Packaging and Distribution Environ-mentsD4332 Practice for C
8、onditioning Containers,Packages,orPackaging Components for TestingD4577 Test Method for Compression Resistance of a Con-tainer Under Constant LoadE4 Practices for Force Calibration and Verification of Test-ing MachinesE122 Practice for Calculating Sample Size to Estimate,WithSpecified Precision,the
9、Average for a Characteristic of aLot or Process3.Terminology3.1 DefinitionsGeneral definitions for the packaging anddistribution environments are found in Terminology D996.3.2 Definitions of Terms Specific to This Standard:3.2.1 constant loada load that is invariable or unchanging.3.2.2 creepcontinu
10、ed deformation over time while underconstant load.3.2.3 loadthe force applied to a body.3.2.4 static loadan imposed stationary force,constant inmagnitude and direction.4.Significance and Use4.1 In the distribution system,the packaged product may bestored for a period of time in a manner such that on
11、e or morecontainers are stacked on one another.The bottom package isthus continually subjected to a constant compression load.4.2 This test method subjects an empty container to apredetermined static load and to specified atmosphericconditions,if required,over a short period of time using fixedplate
12、n compression testing equipment.Deflection is measuredover time.1This test method is under the jurisdiction of ASTM Committee D10 onPackaging and is the direct responsibility of Subcommittee D10.21 on ShippingContainers and Systems-Application of Performance Test Methods.Current edition approved May
13、 1,2022.Published May 2022.Originallyapproved in 2004.Last previous edition approved in 2017 as D7030 04(2017).DOI:10.1520/D7030-04R22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume informa
14、tion,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was develop
15、ed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.14.3 Deflection versus ti
16、me data can be used to predict timeto failure of corrugated shipping containers under constantload.5.Apparatus5.1 Fixed-Platen Testing MachineTwo platens,flat towithin 0.01 in.(0.25 mm)for each 12 in.(304.8 mm)in length,one of which is movable in the vertical direction so as tocompress the container between the platens.One is the loadmeasuring platen,and both should be of sufficient size so thatthe test container does not extend beyond the edges of theplatens.Both platens are fixed in the horizo