1、Designation:D683402(Reapproved 2008)Standard Test Method forDetermining Product Leakage from a Package with aMechanical Pump Dispenser1This standard is issued under the fixed designation D6834;the number immediately following the designation indicates the year oforiginal adoption or,in the case of r
2、evision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the evaluation of the ability ofa pump dispenser to seal when the packaging is
3、held undervacuum.Furthermore,it evaluates the seal between the pumpdispenser and the neck container/closure integrity.1.2 The values stated in SI units are to be regarded asstandard.The values given in parentheses are mathematicalconversions to inch-pound units that are provided for informa-tion onl
4、y and are not considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitatio
5、ns prior to use.See 4.3 for a specific warning statement.2.Referenced Documents2.1 ASTM Standards:2D999 Test Methods for Vibration Testing of Shipping Con-tainersD3198 Test Method for Application and Removal Torque ofThreaded or Lug-Style Closures3.Significance and Use3.1 This test method is suitabl
6、e for establishing specifica-tions of product leakage for both the pump dispenser and thefinal package.The test is performed at two levels of vacuum,alow and a high level,in order to avoid going directly fromatmospheric pressure to 200 mbar,which can sometimes causepump components that had not been
7、fully seated,to seat.3.1.1 Method A,Product Leakage Test without VibrationTesting of a Mechanical Pump Dispenser Package,is usedwhen a pre-conditioning of the package in a simulated shippingsituation is not desired.3.1.2 Method B,Product Leakage Test with Vibration Test-ing of a Mechanical Pump Disp
8、enser Package,is used when apre-conditioning of the package in a simulated shippingsituation is desired.The dynamics and stresses of shipping cancreate conditions where the package may be more likely toleak.4.Apparatus4.1 Vacuum Chamber,with a minimum capacity of 200mbar(147 mm Hg).4.2 Absorbent Pap
9、er.NOTE1Alcoholsensitive paper may be useful in verifying the pointsof leakage for alcohol based products since it is permanently stained withalcohol upon contact.4.3 WarningAppropriate handling consideration shouldbe given to flammable,toxic,caustic,or other potentiallyhazardous materials used in t
10、his determination.5.Sampling5.1 Select an appropriate number of dry,unused pumpdispensers at random for the precision and accuracy desired.Anumber of ten or more samples is recommended,but aminimum of three is acceptable.6.Conditioning6.1 If possible,condition the test specimen at 23 6 3C(736 5.4F)f
11、or not less than 4 h.If the test specimens are notconditioned at the recommended temperature,this should benoted in the test report discussed in 9.1.7.Test Specimen and Sample7.1 For each test specimen select a container to which thepump dispenser will be attached during the test.The actualbottle fo
12、r final package is recommended for testing.8.ProceduresMETHOD APRODUCT LEAKAGE TEST WITHOUTVIBRATION TESTING OF A MECHANICAL PUMPDISPENSER PACKAGE8.1 Fill each container with the liquid to be tested at theactual level of the final package target weight.1This test method is under the jurisdiction of
13、ASTM Committee D10 onPackaging and is the direct responsibility of Subcommittee D10.33 on MechanicalDispensers.Current edition approved Oct.1,2008.Published November 2008.Originallyapproved in 2002.Last previous edition approved in 2002 as D6834 02.DOI:10.1520/D6834-02R08.2For referenced ASTM standa
14、rds,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-295
15、9.United States1 8.2 Attach the pump dispenser securely to the container.Formechanical pump dispenser packages using a threaded orlug-style closure,follow Test Method D3198 for the propermethod of closure application.Take care not to actuate thepump dispenser during this step.8.3 Line the vacuum cha
16、mber shelves with the absorbentpaper.The paper should be absent of stains so that it is easierto identify any leakage during the test.8.4 Lay one or more containers on their side in the vacuumchamber.NOTE2Packages should be oriented such that possible leakage pointsare visible when the vacuum chamber door is closed.8.5 With the door of the vacuum chamber closed,start thepump and bring the vacuum level to a maximum of 850 mbar(absolute pressure,equal to 163 mbar).8.5.1 Hold this level of vacuum f
