1、Designation:D751317Standard Test Method forCapacity of Mixed Bed Ion Exchange Cartridges1This standard is issued under the fixed designation D7513;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in
2、parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the determination of the perfor-mance of mixed bed ion exchange resin cartridges in the activeform when used for deionization
3、.The test can be used todetermine the initial capacity of unused cartridges or theremaining capacity of used cartridges.In this case performanceis defined as ion exchange capacity(or throughput)to twodefined endpoints.The method does not measure organics anddoes not attempt to determine the ultimate
4、 water qualityattainable by the cartridge.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the u
5、ser of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on
6、 Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1125 Test Methods for Electrical Conductivity and Resis-tivity of WaterD1129 Terminology Re
7、lating to WaterD1193 Specification for Reagent WaterD3375 Test Method for Column Capacity of ParticulateMixed Bed IonExchange MaterialsD5391 Test Method for Electrical Conductivity and Resis-tivity of a Flowing High Purity Water Sample3.Terminology3.1 Definitions:3.1.1 For definitions of terms used
8、in this standard,refer toTerminology D1129.4.Summary of Test Method4.1 This test method consists of exhausting a cartridge ofmixed bed ion exchange material to a specific end point with aninfluent solution of known composition and volume.5.Significance and Use5.1 This test method can be used to eval
9、uate unused mixedbed ion exchange cartridges for conformance to specifications.5.2 This test method provides for the calculation of capacityin terms of the volume of water treated to a conductivity endpoint.5.3 The test method as written assumes that the ion ex-change resins in the cartridge are eit
10、her partially or fullyconverted to the H+or OHform.Regeneration of the resins isnot part of this method.5.4 This test method provides for the calculation of capacityon a cartridge basis.5.5 This test method may be used to test different size mixedbed resin cartridges.The flow rate of test water and
11、thefrequency of sampling are varied to compensate for theapproximate volume of resin in the test cartridge.6.Apparatus6.1 Test Assembly(Fig.1),consisting of the following:6.1.1 Cartridge,and pressure vessel,if required.Connec-tions shall be provided at the top and the bottom for theadmission and rem
12、oval of the ion exchange test water asdescribed in 7.4.2.6.1.2 Test solution tank.Adequate means of regulating andmeasuring flow through the cartridge shall be provided.If thetest flow rate(8.1)can not be obtained by gravity feed,then apump should be used.6.1.3 Measuring circuit and in-line conducti
13、vity cells shallbe as described in Test Methods D1125 or D5391.A continu-ous recorder is recommended.1This test method is under the jurisdiction of ASTM Committee D19 on Waterand is the direct responsibility of Subcommittee D19.08 on Membranes and IonExchange Materials.Current edition approved June
14、1,2017.Published June 2017.Originallyapproved in 2009.Last previous edition approved in 2009 as D7513 09.DOI:10.1520/D7513-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refe
15、r to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in
16、 the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 7.Reagents and Materials7.1 Purity of ReagentsReagent grade chemicals shall beused in all tests.Unless otherwise indicated,it is intended thatall reagents shall conform to the specifications of the Commit-tee on Analytical Reagents of the American Chemical Society,where such specifications are available.3Other grad
