收藏 分享(赏)

ASTM_D_6944_-_15.pdf

上传人:益****师 文档编号:170889 上传时间:2023-03-04 格式:PDF 页数:3 大小:78.01KB
下载 相关 举报
ASTM_D_6944_-_15.pdf_第1页
第1页 / 共3页
ASTM_D_6944_-_15.pdf_第2页
第2页 / 共3页
ASTM_D_6944_-_15.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D694415Standard Practice forDetermining the Resistance of Cured Coatings to ThermalCycling1This standard is issued under the fixed designation D6944;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revisio

2、n.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice determines the resistance of cured coatingsor coating systems to repeated thermal cycles and is designedto assess the eff

3、ect of thermal cycling on the properties of acoating or coating system.These properties may includeadhesion,resistance to checking,cracking,blistering,or others.This procedure is not intended to provide a quantitativemeasure of the service life that can be expected from a specificcoating system on a

4、 given substrate.1.2 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2

5、.Referenced Documents2.1 ASTM Standards:2D660 Test Method for Evaluating Degree of Checking ofExterior PaintsD661 Test Method for Evaluating Degree of Cracking ofExterior PaintsD714 Test Method for Evaluating Degree of Blistering ofPaintsD3359 Test Methods for Measuring Adhesion by Tape TestD4541 Te

6、st Method for Pull-Off Strength of Coatings UsingPortable Adhesion TestersD6132 Test Method for Nondestructive Measurement of DryFilm Thickness of Applied Organic Coatings Using anUltrasonic Coating Thickness GageD6677 Test Method for Evaluating Adhesion by KnifeD7091 Practice for Nondestructive Mea

7、surement of DryFilm Thickness of Nonmagnetic Coatings Applied toFerrous Metals and Nonmagnetic,Nonconductive Coat-ings Applied to Non-Ferrous MetalsD7234 Test Method for Pull-Off Adhesion Strength of Coat-ings on Concrete Using Portable Pull-Off Adhesion Tes-tersG147 Practice for Conditioning and Ha

8、ndling of Nonmetal-lic Materials for Natural and Artificial Weathering Tests3.Summary of Test Methods3.1 Test Method ACured test specimens are subjected to30 thermal cycles of immersion,freezing and heating.3.2 Test Method BCured test specimens are subjected to30 thermal cycles of freezing and heati

9、ng.4.Significance and Use4.1 The purpose of this test is to obtain information on theability of a coating system to adhere to substrates underthermal stress.It is assumed that the coating systems tested areapplied and cured according to the coating manufacturersinstructions.TEST METHOD AFREEZE/THAW/

10、IMMERSION5.Apparatus5.1 Thermal Cycling Apparatus:5.1.1 The thermal cycling apparatus shall consist of asuitable chamber or chambers in which the test specimens mayundergo the specified cycle.Ideally,a chamber which containsheating and refrigeration equipment and immersion capabilitiesin the same un

11、it should be used.This chamber shall have theability to maintain continuous reproducible cycles within thespecified temperature requirements.In the event that an appa-ratus having freezing,heating,and immersion capabilities isnot available,separate equipment for freezing,heating andimmersion may be

12、used.5.1.2 The chamber or chambers shall have the ability tomaintain a constant temperature during each of the respectivetemperature intervals as specified by the procedure.5.1.3 The samples shall be arranged to minimize contactwith the chamber surfaces or any mounting racks,and tomaximize air flow.

13、1This practice is under the jurisdiction of ASTM Committee D01 on Paint andRelated Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.46 on Industrial Protective Coatings.Current edition approved July 1,2015.Published July 2015.Originally approvedin 2003.Last pre

14、vious edition approved in 2009 as D6944 091.DOI:10.1520/D6944-15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.C

15、opyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 5.1.4 The temperature of the thermal cycling apparatus shallgive uniform readings at various locations within the chamber,within 3C(5F)at any given time,except during the transitionbetween he

16、ating and freezing cycles.A two hour temperatureramping period is permitted for the equipment to reach the nexttemperature setting.6.Test Specimens6.1 Apply each coating or coating system onto the substratetype and thickness as agreed upon.Preparation of the substrate(that is,surface cleanliness and roughness)prior to applicationof the coating or coating system shall be agreed upon.Measurethe thickness of each coating layer in accordance with PracticeD7091(metallic substrates)or Test Method D613

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2