收藏 分享(赏)

ASTM_D_7755_-_11_2022.pdf

上传人:益****师 文档编号:171052 上传时间:2023-03-04 格式:PDF 页数:5 大小:201.35KB
下载 相关 举报
ASTM_D_7755_-_11_2022.pdf_第1页
第1页 / 共5页
ASTM_D_7755_-_11_2022.pdf_第2页
第2页 / 共5页
ASTM_D_7755_-_11_2022.pdf_第3页
第3页 / 共5页
ASTM_D_7755_-_11_2022.pdf_第4页
第4页 / 共5页
ASTM_D_7755_-_11_2022.pdf_第5页
第5页 / 共5页
亲,该文档总共5页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D775511(Reapproved 2022)Standard Practice forDetermining the Wear Volume on Standard Test Pieces Usedby High-Frequency,Linear-Oscillation(SRV)Test Machine1This standard is issued under the fixed designation D7755;the number immediately following the designation indicates the year oforigi

2、nal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice covers a procedure for determining thewear volume WVof we

3、ar scars and tracks on test piecestribologically stresses under high-frequency,linear-oscillationmotion using a SRV test machine by means of stylus tipprofilometry.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This stan

4、dard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This internat

5、ional standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committ

6、ee.2.Referenced Documents2.1 ASTM Standards:2D2714 Test Method for Calibration and Operation of theFalex Block-on-Ring Friction and Wear Testing MachineD2782 Test Method for Measurement of Extreme-PressureProperties of Lubricating Fluids(Timken Method)D3702 Test Method for Wear Rate and Coefficient

7、of Fric-tion of Materials in Self-Lubricated Rubbing ContactUsing a Thrust Washer Testing MachineD4175 Terminology Relating to Petroleum Products,LiquidFuels,and LubricantsD5620 Test Method for Evaluating Thin Film Fluid Lubri-cants in a Drain and Dry Mode Using a Pin and Vee BlockTest Machine(Withd

8、rawn 2010)3D5706 Test Method for Determining Extreme PressureProperties of Lubricating Greases Using a High-Frequency,Linear-Oscillation(SRV)Test MachineD5707 Test Method for Measuring Friction and Wear Prop-erties of Lubricating Grease Using a High-Frequency,Linear-Oscillation(SRV)Test MachineD6425

9、 Test Method for Measuring Friction and Wear Prop-erties of Extreme Pressure(EP)Lubricating Oils UsingSRV Test Machine2.2 DIN Standards:4DIN 51631:1999-04 Special-boiling-point spirit Require-ments and testingDIN 51834-3:2008-12 Testing of lubricants Tribologicaltest in translatory oscillation appar

10、atus Part 3:Determi-nation of tribological behaviour of materials in co-operation with lubricantsDIN EN ISO 13565-2:1998 Geometrical Product Specifica-tions(GPS)Surface texture:Profile method;Surfaceshaving stratified functional properties Part 2:Heightcharacterization using linear material ratio cu

11、rve(replacesof DIN 4776:1990:Measurement of surface roughness;parameters RK,RPK,RVK,Mr1,Mr2for the description ofthe material portion)3.Terminology3.1 Definitions:3.1.1 Hertzian contact area,nthe apparent area of contactbetween two non-conforming solid bodies pressed against eachother.3.1.2 Hertzian

12、 contact pressure,nmagnitude of the pres-sure at any specified location in a Hertzian contact area,ascalculated from Hertzs equations of elastic deformation.TheHertzian contact pressure can also be calculated and reportedas maximum value Pmaxin the centre of the contact or asPaverageas average over

13、the total contact area.D41751This practice is under the jurisdiction of ASTM Committee D02 on PetroleumProducts,Liquid Fuels,and Lubricants and is the direct responsibility of Subcom-mittee D02.L0.11 on Tribological Properties of Industrial Fluids and Lubricates.Current edition approved July 1,2022.

14、Published August 2022.Originallyapproved in 2011.Last previous edition approved in 2017 as D7755 11(2017).DOI:10.1520/D7755-11R22.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,

15、refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from Deutsches Institut fur Normung e.V.(DIN),Beuth VerlagGmbH,Burggrafenstrae 6,D-10787 Berlin 30,Germany,http:/www.din.de.Copyright ASTM In

16、ternational,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.13.1.3 seizure,nlocalized fusion of metal between therubbing surfaces of the test pieces.D57063

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2