1、Designation:D763810(Reapproved 2021)Standard Test Method forDetermination of Fatty Acids and Esters in Glycerin1This standard is issued under the fixed designation D7638;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of las
2、t revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method provides the quantitative determinationof the fatty acid and ester content in purified glycerin by thetitrime
3、tric method.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard may involve hazardous materials,opera-tions and equipment.This standard does not purport to addressall of the safety concerns,if any,associated wit
4、h its use.It isthe responsibility of the user of this standard to establishappropriate safety,health,and environmental practices anddetermine the applicability of regulatory limitations prior touse.Specific precautions are listed in Section 8.1.4 This international standard was developed in accor-da
5、nce with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standa
6、rds:2D1193 Specification for Reagent WaterD4725 Terminology for Engine Coolants and Related Fluids2.2 Other Standard:The United States Pharmacopoeia 31 Glycerin Monograph Fatty Acids and Esters33.Terminology3.1 Definitions:3.1.1 glycerinpropane-1,2,3-Triol,C3H5(OH)3(alsoknownasglycerine),1,2,3-propa
7、netriol,1,2,3-trihydroxypropane,glyceritol,glycyl alcohol.CAS#56-81-53.1.2 FA&Efatty acid and esters3.1.3 Forotherdefinitionsoftermsusedinthisspecification,refer to Terminology D4725.4.Significance and Use4.1 Any residual fatty acid and esters(FA&E)should bepresent only at very low levels in purifie
8、d glycerine.4.2 This procedure requires the addition of a measuredvolume of sodium hydroxide,in excess of the amount actuallyneeded to react with FA&E in the glycerine sample.Afterboiling,the excess sodium hydroxide is back titrated withstandardized hydrochloric acid.The quantity of the substancebei
9、ng titrated is calculated as the difference between thevolumes of the sodium hydroxide solution originally added,corrected by means of a blank titration,and that was consumedby the titrant in the back titration.NOTE1The standardized solutions for sodium hydroxide and hydro-chloric acid are commercia
10、lly available.5.Apparatus5.1 Standard Type A Glassware.5.2 Erlenmeyer flask,200 mL to 250 mL,alkali-resistantwith a standard tapered 24/40 ground glass neck joint,orequivalent.5.3 Microburette having a capacity of 5 mL,graduated to0.02 mL and calibrated to meet the National Institute ofStandards and
11、 Technology(NIST)specification.An automatictitrator with a minimum capacity of 5 mL can also be used.5.4 Pipette,standard or automatic that can accurately de-liver 5 mL 6 0.01 mL.5.5 Air reflux condenser with standard taper ground glassjoint which fits the Erlenmeyer flask in 5.1.Minimum length,550
12、mm.6.Purity of Reagents and Water6.1 Purity of ReagentsReagent grade chemicals shall beused in all tests.Unless otherwise indicated,it is intended thatall reagents conform to the specifications of the Committee on1This test method is under the jurisdiction of ASTM Committee D15 on EngineCoolants and
13、 Related Fluids and is the direct responsibility of SubcommitteeD15.04 on Chemical Properties.Current edition approved Sept.1,2021.Published September 2021.Originallyapproved in 2010.Last previous edition approved in 2015 as D763810(2015).DOI:10.1520/D7638-10R21.2For referenced ASTM standards,visit
14、the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from U.S.Pharmacopeial Convention(USP),12601 TwinbrookPkwy.,Rockville,MD 20852-1790,http:/ww
15、w.usp.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of
16、International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1Analytical Reagents of the American Chemical Society wheresuch specifications are available.Other grades may be usedprovided it is first ascertained that the reagent is of sufficientlyhigh purity to permit its use without lessening the accuracy ofthe determination.6.2 Purity of WaterUnless indicated otherwise,referencesto water shall be understood to mean Type II r
