1、Designation:D739418Standard Practice forRheological Characterization of Architectural Coatingsusing Three Rotational Bench Viscometers1This standard is issued under the fixed designation D7394;the number immediately following the designation indicates the year oforiginal adoption or,in the case of r
2、evision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice describes a popular industry protocol forthe rheological characterization of waterborne a
3、rchitecturalcoatings using three commonly used rotational bench viscom-eters.Each viscometer operates in a different shear rate regimefor determination of coating viscosity at low shear rate,midshear rate,and at high shear rate respectively as defined herein.General guidelines are provided for predi
4、cting some coatingperformance properties from the viscosity measurementsmade.With appropriate correlations and subsequent modifica-tion of the performance guidelines,this practice has potentialfor characterization of other types of aqueous and non-aqueouscoatings.1.2 The values in common viscosity u
5、nits(Krebs Units,KUand Poise,P)are to be regarded as standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine
6、 the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations is
7、sued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D562 Test Method for Consistency of Paints MeasuringKrebs Unit(KU)Viscosity Using a Stormer-Type Viscom-eterD869 Test Method for Evaluating Degree of Settling of PaintD1005 Test Me
8、thod for Measurement of Dry-Film Thick-ness of Organic Coatings Using MicrometersD1200 Test Method for Viscosity by Ford Viscosity CupD2196 Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational ViscometerD2805 Test Method for Hiding Power of Paints by Reflec-tometryD4040 T
9、est Method for Rheological Properties of PastePrinting and Vehicles by the Falling-Rod ViscometerD4062 Test Method for Leveling of Paints by Draw-DownMethodD4287 Test Method for High-Shear Viscosity Using a Cone/Plate ViscometerD4400 Test Method for Sag Resistance of Paints Using aMultinotch Applica
10、torD4414 Practice for Measurement of Wet Film Thickness byNotch GagesD4958 Test Method for Comparison of the Brush Drag ofLatex Paints3.Terminology3.1 Definitions:3.1.1 coating rheology,nthe viscosity profile obtained fora fluid coating over a range of shear rates.3.1.2 high-shear viscosity(HSV),nth
11、e viscosity of a fluidcoating at high shear rate(typically measured at 10,000 s-1or12,000 s-1),and for architectural coatings,it is often referred toas the“brush-drag”viscosity.3.1.3 leveling,nthe ability of a wet coating to flow out toa smooth dry film after application,thereby minimizing orelimina
12、ting coating surface irregularities that occur duringbrushing,rolling or spraying(see also Test Method D4062).3.1.4 low-shear viscosity(LSV),nthe viscosity of a coat-ing fluid at low shear rate(typically in the range of 0.001 s-1to1 s-1),often referred to as the“leveling viscosity”or inverselyas the
13、“suspension viscosity.”3.1.5 mid-shear thickener effciency(MSTE),nthe weightof active thickener per unit volume of wet coating required togive the target MSV,commonly expressed as lb activethickener/100 gal wet coating(or in g/L units).1This practice is under the jurisdiction of ASTM Committee D01 o
14、n Paint andRelated Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.24 on Physical Properties of Liquid Paints and Paint Materials.Current edition approved June 1,2018.Published June 2018.Originallyapproved in 2008.Last previous edition approved in 2017 as D739
15、4 17.DOI:10.1520/D7394-18.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Ha
16、rbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.1.6 mid-shear viscosity(MSV),nthe viscosity of acoating fluid at medium shear rate(typically in the range of 10s-1
